. In the third video you can hear the tractor "rolling" at mid throttle. You can see the govenor bouncing a little.I hope you enjoy!
Bolens 1250 running videos
Started by
PennsylvaniaNewt
, Nov 06, 2011 09:27 PM
8 replies to this topic
#1
OFFLINE
PennsylvaniaNewt
-
- Senior Member
- Member No: 5693
- 58 Thanks
- 169 posts
Member
Posted November 06, 2011 - 09:27 PM
Here are some videos of the rebuilt Wisconsin running . In the third video you can hear the tractor "rolling" at mid throttle. You can see the govenor bouncing a little.
I hope you enjoy!
. In the third video you can hear the tractor "rolling" at mid throttle. You can see the govenor bouncing a little.I hope you enjoy!
- mikebramel said thank you
#2
ONLINE
Bolens 1000
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 7
- 14,219 Thanks
- 17,846 posts
DR. Bolens
- Location: Western NY
Posted November 07, 2011 - 05:41 AM
Sounds Great! 
#3
OFFLINE
awol
-
- Senior Member
- -GTt Supporter-
- Member No: 1576
- 77 Thanks
- 341 posts
Tractorholic
- Location: Smiths Falls Ontario Canada
Posted November 07, 2011 - 06:19 AM
Thanks for the video, It sure sounds good!!
#4
ONLINE
LPBolens
-
- Senior Member
- -GTt Supporter-
- Contributor
- Member No: 874
- 1,284 Thanks
- 928 posts
Tractorholic
- Location: North Central Illinois
Posted November 07, 2011 - 01:50 PM
Sounds good to me!
If you are really concerned about the slight surging at mid throttle, you could do what the manual says to adjust the governor linkage. WITH THE ENGINE OFF, and with the linkage disconnected at the governor arm, hold the throttle wide open with the long linkage rod. The linkage rod should then be adjusted using the threaded end adjustment so that the bent end will slip into the hole on the governor arm. The governor spring will hold the flyweights in so the governor arm should be in the proper, no RPM position.
If you are really concerned about the slight surging at mid throttle, you could do what the manual says to adjust the governor linkage. WITH THE ENGINE OFF, and with the linkage disconnected at the governor arm, hold the throttle wide open with the long linkage rod. The linkage rod should then be adjusted using the threaded end adjustment so that the bent end will slip into the hole on the governor arm. The governor spring will hold the flyweights in so the governor arm should be in the proper, no RPM position.
#5
OFFLINE
mjodrey
-
- Senior Member
- Contributor
- Member No: 92
- 2,353 Thanks
- 13,481 posts
Accumulator
- Location: Upper Granville, Nova Scotia, Canada
Posted November 07, 2011 - 04:39 PM
That does sound nice,thanks for the videos.
#6
ONLINE
wilberj
-
- Senior Member
- -GTt Supporter-
- Contributor
- Member No: 51
- 4,732 Thanks
- 5,467 posts
- Location: Michigan
Posted November 07, 2011 - 08:50 PM
Is the choke still on looks pulled out?
#7
OFFLINE
PennsylvaniaNewt
-
- Senior Member
- Member No: 5693
- 58 Thanks
- 169 posts
Member
Posted November 08, 2011 - 10:44 PM
The choke was off! I re-adjusted the governor linkage and it now runs smoother :-)
#8
OFFLINE
JJuday
-
- Member
- Member No: 5194
- 4 Thanks
- 47 posts
Member
- Location: Howe, IN.
Posted November 10, 2011 - 04:55 PM
It still amazes me how quiet and quick those old Wisconsins pop off. That is an awesome tractor! I think the seat pan/foot rest set up on the older tube frames were better than the latter series with the smallish individual steps and I always liked the horizontal pipe on the left. Cool machines.
- PennsylvaniaNewt said thank you
#9
OFFLINE
PennsylvaniaNewt
-
- Senior Member
- Member No: 5693
- 58 Thanks
- 169 posts
Member
Posted November 10, 2011 - 07:34 PM
Thanks!
