Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Prestolite Actuator


  • Please log in to reply
8 replies to this topic

#1 DanP OFFLINE  

DanP

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 6989
  • 276 Thanks
  • 467 posts
  • Location: Mt Pleasant, Iowa

Posted October 26, 2011 - 01:07 PM

Anyone know where you can get replacement parts ie motor for the electric hydraulic lift motors like on a 1200 or 1600 series? It is a Prestolite 106152. It was laying around our shop and I think the motor was bad. I took it apart and the motor is all rusted to a point I can't even get the aramature out.

#2 DanP OFFLINE  

DanP

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 6989
  • 276 Thanks
  • 467 posts
  • Location: Mt Pleasant, Iowa

Posted October 26, 2011 - 08:31 PM

So after some research it is a Hydraulic power lift off a MF10 522748 M91. The electric motor is shot so I still need to find one or get it fixed if anyone can help.

#3 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 28,508 Thanks
  • 39,733 posts
  • Location: Collinsville, Oklahoma

Posted October 27, 2011 - 07:11 AM

Cant help you, Dan. But at least I can bump this back up.

#4 IamSherwood OFFLINE  

IamSherwood

    Elf guardian

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 2066
  • 8,379 Thanks
  • 7,696 posts
  • Location: Northern Ontario

Posted October 27, 2011 - 10:11 AM

Pretty sure those things are kinda rare. You should try to get it fixed. Take it to an automotive electric repair shop. They do starters/ alternators. They might
be able to help you.

#5 DanP OFFLINE  

DanP

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 6989
  • 276 Thanks
  • 467 posts
  • Location: Mt Pleasant, Iowa

Posted October 27, 2011 - 04:20 PM

@ IamSherwood, do you think that little elctric lift will work on a 3 point? I can get the motor repaired for around $90-$150. I am not sure it will have enough power though to lift much. I plan on making or buying a rear blade and a rear 3 point rotary cutter (I have yet to make this). Neither one of these will be that heavy but they will stick out a ways behind the tractor making them more difficult to lift. I could make a hydraulic system for the tractor but that is a lot of work. If this electric unit wont work I would rather spend the money on the hydraulics.

#6 IamSherwood OFFLINE  

IamSherwood

    Elf guardian

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 2066
  • 8,379 Thanks
  • 7,696 posts
  • Location: Northern Ontario

Posted October 27, 2011 - 05:38 PM

Dan, sorry,I don't know how much umpf those guys have. It's electric over hydraulics, so it may produce enough.
Probably stronger than a straight electric linear actuator.
My understanding is that they attached to the manual lift lever. That lever also raised and lowered the sleeve hitch.
That sleeve hitch linkage also raised the rototiller. I have one on my 12. There is a lot of weight to that tiller, and
requires a good pull to raise it.
You might want to check with member Tweidman. I think he has one, and may be able to shed some light.

#7 DanP OFFLINE  

DanP

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 6989
  • 276 Thanks
  • 467 posts
  • Location: Mt Pleasant, Iowa

Posted October 27, 2011 - 08:26 PM

Would you mind sending me a picture of how it is mounted? Unless it is behind tin work then don't bother. I still have a lot of old Massey books I can probably find it in there.

#8 IamSherwood OFFLINE  

IamSherwood

    Elf guardian

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 2066
  • 8,379 Thanks
  • 7,696 posts
  • Location: Northern Ontario

Posted October 27, 2011 - 08:57 PM

missunderstanding here. I meant that I have a rototiller on my 12. I don't have one of those lifts to take a pic of.

#9 DanP OFFLINE  

DanP

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 6989
  • 276 Thanks
  • 467 posts
  • Location: Mt Pleasant, Iowa

Posted November 07, 2011 - 04:44 PM

Does anyone have a picture of how the electric hydraulic power lift is mounted to a MF10. Also any mounting or electrical information? I am missing the solinoid and need some info on it.




Top