Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Anybody got a pulley


  • Please log in to reply
11 replies to this topic

#1 mrolds88 OFFLINE  

mrolds88

    Member

  • Member
  • Member No: 6584
  • 2 Thanks
  • 13 posts

Posted September 28, 2011 - 10:27 PM

Hello all!! I have an old MTD built Wizard that I am in need of a pulley for. i need the transaxle input pulley. Its got a 2300 series Peerless 4 speed cast iron unit. iIt is about 7" OD and 3/4" x 48 spline ID. Anybody got onr laying around? In case you are wondering what machine I have, I use a parts diagram for model 137-812-002. Thanks!!:wave:

#2 MH81 OFFLINE  

MH81

    Proud to be Deplorable

  • Staff Admin
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 802
  • 27,341 Thanks
  • 28,646 posts
  • Location: N. W. PA

Posted September 29, 2011 - 12:10 AM

:welcome: to GTTalk.

I don't have any splined shaft trannys. Wish I could help, maybe someone will give you a lead.

#3 caseguy OFFLINE  

caseguy

    Connoisseur of Rusty Junk

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 906
  • 1,624 Thanks
  • 5,600 posts
  • Location: Edinburg, PA

Posted September 29, 2011 - 07:05 PM

You could check into one of our site supporters and see if they have any or could try looking at your local mower repair shop.

#4 trowel OFFLINE  

trowel

    Summer.

  • Senior Member
  • -GTt Supporter-
  • Member No: 5127
  • 4,819 Thanks
  • 4,533 posts
  • Location: ma.

Posted September 29, 2011 - 07:13 PM

Welcome to GT Talk, good to have you,

#5 tractorgarden OFFLINE  

tractorgarden

    Junk Whisperer

  • Senior Member
  • -GTt Supporter-
  • Member No: 2291
  • 1,277 Thanks
  • 1,432 posts
  • Location: northwest pa

Posted September 29, 2011 - 07:27 PM

Welcome to GTTalk Mr. Olds 88, sorry I do not have any, But I have a Olds engine pict . :wave: Olds at the Farm - Close up.jpg I you hope find what you need. Check out our member map,and jump in the chat room if you see an one in there, It is also a great place to find spare parts! Shawn

Attached Thumbnails

  • Engine- Nolfi.jpg


#6 mrolds88 OFFLINE  

mrolds88

    Member

  • Member
  • Member No: 6584
  • 2 Thanks
  • 13 posts

Posted September 29, 2011 - 08:26 PM

Thanks All!! NIce 66 Shawn! I had a 67 at one time, but I got it after it was wrecked. Anyway, MIght have to hit the chat room sometime. Don't have many repair shops in the area, and since this is out of an 80's machine, guess I will just have to keep lookin. I did but an old Sears tractor for parts, but decided to keep it. Turns out it was a 76 ST/8. Has the same rear, thats the reason I bought it, but its an oddball. So it stays. More on that in anothr forum. Later!

#7 cityboy2977 OFFLINE  

cityboy2977

    ordinary average guy

  • Senior Member
  • Member No: 6650
  • 117 Thanks
  • 179 posts
  • Location: Mancelona, Michigan

Posted October 02, 2011 - 11:05 AM

check with these folks
Lawn Mower Parts, Military Surplus, and everything in between at Glen's Surplus

good luck
  • mrolds88 said thank you

#8 mrolds88 OFFLINE  

mrolds88

    Member

  • Member
  • Member No: 6584
  • 2 Thanks
  • 13 posts

Posted October 04, 2011 - 06:45 PM

Thanks cityboy! They have one that looks right. I messaged them, just waiting for a reply.

#9 dstaggs OFFLINE  

dstaggs

    In Remembrance, RIP Dale

  • RIP
  • -GTt Supporter-
  • Member No: 228
  • 553 Thanks
  • 1,781 posts
  • Location: Batesville, Arkansas

Posted October 04, 2011 - 07:33 PM

Welcome to GTtalk. I have some old sears GTs. But none junked out.

#10 cityboy2977 OFFLINE  

cityboy2977

    ordinary average guy

  • Senior Member
  • Member No: 6650
  • 117 Thanks
  • 179 posts
  • Location: Mancelona, Michigan

Posted October 04, 2011 - 08:48 PM

right on! glad i could help

#11 mrolds88 OFFLINE  

mrolds88

    Member

  • Member
  • Member No: 6584
  • 2 Thanks
  • 13 posts

Posted October 10, 2011 - 04:01 PM

Just got a reply to my email to Glens. The pulley that I saw, wont work. Guess I am back on the lookout. They did have a gas tank for another mower I have.

#12 cedarjunki OFFLINE  

cedarjunki
  • Member
  • Member No: 8708
  • 3 Thanks
  • 27 posts
  • Location: upstate ny

Posted February 23, 2012 - 05:50 AM

Hello all!! I have an old MTD built Wizard that I am in need of a pulley for. i need the transaxle input pulley. Its got a 2300 series Peerless 4 speed cast iron unit. iIt is about 7" OD and 3/4" x 48 spline ID. Anybody got onr laying around? In case you are wondering what machine I have, I use a parts diagram for model 137-812-002. Thanks!!:wave:


i will check, i had a couple i picked up at one point, but not sure if my kid got to them.... if your still looking... ill let you know.




Top