Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

picked up a 10


  • Please log in to reply
10 replies to this topic

#1 Stoneman OFFLINE  

Stoneman

    Masseyholic

  • Senior Member
  • Member No: 1763
  • 26 Thanks
  • 157 posts
  • Location: Hutchinson MN

Posted July 20, 2011 - 01:58 PM

It's rough, but i think it's savable :D. The dash is junk, there's no hood, no grill, the pto shaft under the frame is missing and a few other parts. It has an hh120 that turns over with good compression but no spark, all the gears seem good and i already got the bent fender looking (similar) to the good one and i got all 4 tires to hold air.

My plan it to make it a work horse, so I've also got my eye on some parts on ebay!

duck 020.jpg

And last... does anyone have the demensions of the rod the goes from the lift lever to the pivoting shaft that would lift the mower, blade....ect
It's number 35 here under the first tab (Frame, Brake, and Lift Linkage)

AGCO Parts Books

Thanks for any help

Attached Thumbnails

  • duck 016.jpg
  • duck 017.jpg
  • duck 021.jpg
  • duck 019.jpg


#2 tweidman OFFLINE  

tweidman

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 5
  • 250 Thanks
  • 797 posts
  • Location: Ackermanville,Pa

Posted July 20, 2011 - 02:50 PM

Is it a 10 with the wrong engine, or is it a 12G? Are you going to do a 'Stoller' conversion on it?

#3 Stoneman OFFLINE  

Stoneman

    Masseyholic

  • Senior Member
  • Member No: 1763
  • 26 Thanks
  • 157 posts
  • Location: Hutchinson MN

Posted July 20, 2011 - 03:04 PM

On the plate on the side it says MF10. after looking the engine over it looks like the origanal engine but with a different blower howsing. a diesel repower came to mind but i think i'll stick with what i got, my uncle has two solid state ignition vertical shaft cast iron engines and one of them runs so i think i'll try to make the origanal SSI work. If not........possibly Diesel :D (If money allows it)

Edited by Stoneman, July 20, 2011 - 03:50 PM.


#4 mikebramel OFFLINE  

mikebramel

    Ron Paul

  • Senior Member
  • Member No: 82
  • 176 Thanks
  • 1,009 posts
  • Location: Milwaukee

Posted July 20, 2011 - 04:44 PM

Good buy with the sleeve hitch

#5 DH1 OFFLINE  

DH1

    Electric Tractors

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 62
  • 4,587 Thanks
  • 5,295 posts
  • Location: Markham Ontario Canada

Posted July 20, 2011 - 08:07 PM

masseys 071..jpg

The longer rod with the bend in it is for Hydro's
The short straight rod is for gear drives.
If nothing else you got lots of parts there.

Attached Thumbnails

  • masseys 070..jpg

  • Stoneman said thank you

#6 IamSherwood OFFLINE  

IamSherwood

    Elf guardian

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 2066
  • 8,379 Thanks
  • 7,696 posts
  • Location: Northern Ontario

Posted July 20, 2011 - 08:13 PM

Sorry, can't give you a dimension, till maybe Sunday, but here is a picture.

Looks like you got a good project there.

Attached Thumbnails

  • P1010110.jpg

  • Stoneman said thank you

#7 Stoneman OFFLINE  

Stoneman

    Masseyholic

  • Senior Member
  • Member No: 1763
  • 26 Thanks
  • 157 posts
  • Location: Hutchinson MN

Posted July 20, 2011 - 08:48 PM

I should have been more specific of what i was looking for, Thanks Will that's the one i was try to describe. if you could get me the length sometime that would be great. (it's not a rush). I wont be using it any time soon being i don't have the PTO shaft. once i locate that the only parts i'll be missing is the hood and grill. there's one on eBay right now, i think in a month if it's still there i'll buy it. and because my plans for it are to make it a work horse a hood and grill is not a necessity.:D

#8 IamSherwood OFFLINE  

IamSherwood

    Elf guardian

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 2066
  • 8,379 Thanks
  • 7,696 posts
  • Location: Northern Ontario

Posted July 20, 2011 - 08:53 PM

I will get you that measurement soon. I might have an extra one, but you could probably make one cheaper than shipping cost.

#9 Stoneman OFFLINE  

Stoneman

    Masseyholic

  • Senior Member
  • Member No: 1763
  • 26 Thanks
  • 157 posts
  • Location: Hutchinson MN

Posted July 20, 2011 - 08:56 PM

to make one was my plan, doesn't look too hard to copy (even with my skills) LOL thanks again for the help

#10 DH1 OFFLINE  

DH1

    Electric Tractors

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 62
  • 4,587 Thanks
  • 5,295 posts
  • Location: Markham Ontario Canada

Posted July 20, 2011 - 08:59 PM

I should have been more specific of what i was looking for, Thanks Will that's the one i was try to describe. if you could get me the length sometime that would be great. (it's not a rush). I wont be using it any time soon being i don't have the PTO shaft. once i locate that the only parts i'll be missing is the hood and grill. there's one on eBay right now, i think in a month if it's still there i'll buy it. and because my plans for it are to make it a work horse a hood and grill is not a necessity.:D


I just re read the post, I guess I didn't read it good enough the first time???

#11 Stoneman OFFLINE  

Stoneman

    Masseyholic

  • Senior Member
  • Member No: 1763
  • 26 Thanks
  • 157 posts
  • Location: Hutchinson MN

Posted July 23, 2011 - 09:50 PM

I messed around with it a little tonight and found the SSI module to be bad, i took one of the ones from my donor engines and got great spark! i tried driving it but first i need a throttle cable and a little carb adjusting. The origanal SSI system seems like a easy and simple system to work with. too bad the don't carry them anymore.




Top