Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

Ford 200 Disk

ford 3 point hitch 200

  • Please log in to reply
9 replies to this topic

#1 2182Cub OFFLINE  

2182Cub
  • Member
  • Member No: 89529
  • 5 Thanks
  • 2 posts
  • Location: Illinois

Posted February 19, 2018 - 06:31 PM

I'm looking for information on my Ford model 200 3 point disk. I've posted in other forums and someone always comments that is was made by Brinly but I've yet to find any manuals or brochures. If you look closely the braces from the 3 point top link hitch is flat steel where as Brinly 3 pt disk's are round to flat. Any information would be welcomed!

Attached Thumbnails

  • 200disk1.JPG
  • 200disk.JPG

  • boyscout862 and Mark 149 J. have said thanks

#2 IHCubGuy OFFLINE  

IHCubGuy

    Tractorholic

  • Senior Member
  • Member No: 3438
  • 1,616 Thanks
  • 1,639 posts
  • Location: Northumberland Pa

Posted February 19, 2018 - 07:39 PM

Go to messick's parts lookup. Cnh lists the model 200 under new Holland's parts store. Not sure if it's a brinley or not though. It's listed under parts as a disk for an 1100 ford tractor.
  • boyscout862, Mark 149 J. and 2182Cub have said thanks

#3 MiCarl ONLINE  

MiCarl
  • Senior Member
  • Member No: 75926
  • 2,219 Thanks
  • 1,129 posts
  • Location: Livonia, MI

Posted February 19, 2018 - 07:42 PM

BRINLY MODEL DD-1000 3 PT. LIFT TYPE TANDEM DISK HARROW MANUAL


  • boyscout862 and 2182Cub have said thanks

#4 boyscout862 OFFLINE  

boyscout862
  • Senior Member
  • Contributor
  • Member No: 8923
  • 13,693 Thanks
  • 9,476 posts
  • Location: N.E. Connecticut

Posted February 19, 2018 - 08:20 PM

Welcome to GTT.  Tell us about yourself and your tractors. Good Luck, Rick


  • 2182Cub said thank you

#5 shorty ONLINE  

shorty

    Member

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 6172
  • 5,922 Thanks
  • 5,453 posts
  • Location: Lancaster County Pa

Posted February 19, 2018 - 08:35 PM

Since it is so similar to a Brinly, is it possible it was built by Brinly to Ford specs?

#6 2182Cub OFFLINE  

2182Cub
  • Member
  • Member No: 89529
  • 5 Thanks
  • 2 posts
  • Location: Illinois

Posted February 19, 2018 - 09:02 PM

Currently I have a cub cadet 2182, 129, 782 roller, 1650 roller, Ingersoll 4018, AC 312 with tiller, Duetz Allis roller not sure of the model, A JD 330 I bought for my cousin, 8" sleeve hitch plow, 10" sleeve hitch plow, Montgomery Wards sleeve hitch harrow, potato plow, 2 Jacobsen Greens King IV with Kubota D600's for repower projects, and a couple truck loads of parts and 1 wife that rolls her eyes. Planning on putting 1 D600 in my 2182. Retired Maintenance Supervisor, lived on a farm all my life. Sold my Cub 682 and 104, Wheel Horse D200. Oh And I have my Ford 200 3 point disk, still looking for a 3 point hitch tho.  :rolling: 


  • boyscout862, propane1 and Leonard VanCamp have said thanks

#7 IHCubGuy OFFLINE  

IHCubGuy

    Tractorholic

  • Senior Member
  • Member No: 3438
  • 1,616 Thanks
  • 1,639 posts
  • Location: Northumberland Pa

Posted February 19, 2018 - 10:15 PM

Thanks for that reference page there.  I'd say after seeing that there is no doubt about it being a Brinly.  I thought maybe but wasn't sure.  Some of the part numbers are almost a dead match between cnh's parts store and the Brinly part number.

 

https://partstore.ag...mr52142ar127102

 

Reference #1 is a part# BHD161 which I assume the bh means Brinly Hardy.

 

 

http://www.wfmfiles....ow(DD-1000).pdf

 

The same piece in this link posted by MiCarl is reference #10 and it's part# is D-161-10.

 

Most of the other part #'s are the same way so I think the part #'s being all but identical reveal it a Brinly Hardy disk built to Ford specs just as Shorty suggests.


Edited by IHCubGuy, February 19, 2018 - 10:16 PM.

  • shorty and 2182Cub have said thanks

#8 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 41,519 Thanks
  • 47,427 posts
  • Location: Collinsville, Oklahoma

Posted February 20, 2018 - 05:17 AM

:wave:  Welcome to the forum! I'm going to move this to the Implements Forum.


  • shorty, boyscout862 and 2182Cub have said thanks

#9 2182Cub OFFLINE  

2182Cub
  • Member
  • Member No: 89529
  • 5 Thanks
  • 2 posts
  • Location: Illinois

Posted February 22, 2018 - 09:38 AM

Thanks everyone! I agree after seeing the parts diagram and parts number listing starting with bh that it is indeed made by Brinly. I wonder if there are any build numbers for these disks? They must be limited numbers of them around.



#10 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 41,519 Thanks
  • 47,427 posts
  • Location: Collinsville, Oklahoma

Posted February 22, 2018 - 02:59 PM

Thanks everyone! I agree after seeing the parts diagram and parts number listing starting with bh that it is indeed made by Brinly. I wonder if there are any build numbers for these disks? They must be limited numbers of them around.

I've not seen any build #'s anywhere for Brinly stuff.







Also tagged with one or more of these keywords: ford, 3 point hitch, 200

Top