Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

MM 112 Hydro filter

hydro filter 112 hydrostatic

  • Please log in to reply
9 replies to this topic

#1 fyn409 OFFLINE  

fyn409
  • Member
  • Member No: 88227
  • 2 Thanks
  • 5 posts
  • Location: Michigan

Posted September 05, 2017 - 09:12 PM

We recently purchased a 1968 MM 112 Hydro GT.  We are doing some general maintenance items on it, fluid changes, etc.  We drained the oil in the hydro unit and the filter is pretty nasty.  We are attempting to clean it, but are there replacements available?

 

-Ryan


  • Bolens800uk said thank you

#2 Oldford OFFLINE  

Oldford
  • Senior Member
  • -GTt Supporter-
  • Member No: 50409
  • 1,134 Thanks
  • 786 posts
  • Location: n.e.

Posted September 06, 2017 - 03:42 AM

Hi, your MM was likely made by Jacobsen with a Sundstrand hydro.  The filter is JAC545440.  Last available through New Holland and some of the online parts places for around $50 with shipping airc.  You'd have to hunt around to find one on a shelf somewhere.  Same situation with the mower blades if yours has the aluminum deck except they were around $100, if you can still find any, good luck.


  • KennyP, Bolens800uk and fyn409 have said thanks

#3 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 35,791 Thanks
  • 44,563 posts
  • Location: Collinsville, Oklahoma

Posted September 06, 2017 - 07:01 AM

:wave: Welcome to the forum! I think I bought the last one a couple years ago! Haven't found a replacement # as yet.



#4 chieffan OFFLINE  

chieffan
  • Senior Member
  • Contributor
  • Member No: 62695
  • 8,998 Thanks
  • 6,167 posts
  • Location: SW Iowa

Posted September 06, 2017 - 07:29 AM

Check with a Baldwin filter dealer.  Very good filters and can cross to about anything I have found.



#5 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 35,791 Thanks
  • 44,563 posts
  • Location: Collinsville, Oklahoma

Posted September 06, 2017 - 07:49 AM

Check with a Baldwin filter dealer.  Very good filters and can cross to about anything I have found.

I tried their e-catalog cross and they show nothing.



#6 poncho62 ONLINE  

poncho62
  • Senior Member
  • Member No: 42
  • 1,357 Thanks
  • 1,523 posts
  • Location: Hanover, Ont, Canada

Posted September 06, 2017 - 11:43 AM

Is this an inline filter?

 

A lot of people just back flush them with kerosene or another solvent until all the particulates are out of it. 

 

Some replace them with a filter base and spin on filter. I recently did this with my Ford LGT.....cost about $30

 

IMG_1821.JPG

 

 


Edited by poncho62, September 06, 2017 - 11:44 AM.

  • KennyP and Bolens800uk have said thanks

#7 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 35,791 Thanks
  • 44,563 posts
  • Location: Collinsville, Oklahoma

Posted September 06, 2017 - 01:47 PM

Is this an inline filter?

 

A lot of people just back flush them with kerosene or another solvent until all the particulates are out of it. 

 

Some replace them with a filter base and spin on filter. I recently did this with my Ford LGT.....cost about $30

 

attachicon.gifIMG_1821.JPG

Not an inline filter. I have a thread somewhere when I did my Jake.


  • poncho62 said thank you

#8 Dayton_King ONLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 981 Thanks
  • 928 posts
  • Location: Atlanta Georgia

Posted September 07, 2017 - 06:33 AM

When we restored our Mm's and the White we used break cleaner and compressed air and it took a while. I found one filter and they wanted 120 bucks for it on ebay.
  • KennyP said thank you

#9 fyn409 OFFLINE  

fyn409
  • Member
  • Member No: 88227
  • 2 Thanks
  • 5 posts
  • Location: Michigan

Posted September 11, 2017 - 08:06 AM

Thanks for the info on the part number, I will continue to search around and see if I can find anything.  For the moment we have the old one soaking in our parts washer hoping to get it clean enough for now.  If anyone else comes up with something please let me know.


  • Bolens800uk said thank you

#10 Bolens800uk OFFLINE  

Bolens800uk
  • Senior Member
  • Member No: 63893
  • 1,623 Thanks
  • 1,139 posts
  • Location: Devon, England

Posted September 24, 2017 - 04:03 AM

Yes I would be interested in this too.





Also tagged with one or more of these keywords: hydro, filter, 112, hydrostatic

Top