Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

1650 center lift cylinder


  • Please log in to reply
8 replies to this topic

#1 cchap45 OFFLINE  

cchap45

    New Member

  • Member
  • Member No: 6595
  • 88 Thanks
  • 53 posts
  • Location: MN

Posted April 11, 2017 - 09:02 AM

Has anyone rebuilt, know how to rebuild or know somewhere that rebuilds welded hydraulic cylinders?  Thinking about cutting this one apart and trying to fix the leaking seals. This one is an extra I can experiment with before I take on the 3 point lift cylinder that is also leaking.

thanks!

Attached Thumbnails

  • liftcyl.jpg

  • DMAX said thank you

#2 limebuzz ONLINE  

limebuzz

    Member

  • Senior Member
  • Member No: 795
  • 953 Thanks
  • 942 posts
  • Location: Bluevale Ontario

Posted April 11, 2017 - 12:43 PM

Don't cut it. Lol. Clean inside the bottom of it. Then the bottom pushes out after the pin is out. Someone had a thread here about rebuilding these.
  • DMAX, ducky, cchap45 and 1 other said thanks

#3 cchap45 OFFLINE  

cchap45

    New Member

  • Member
  • Member No: 6595
  • 88 Thanks
  • 53 posts
  • Location: MN

Posted April 11, 2017 - 03:03 PM

Thanks, I will look into that.  I had a guy that services heavy equipment look at it and he said it was a throw away.  Gald I came to the experts!



#4 adolphsson09 OFFLINE  

adolphsson09
  • Senior Member
  • Member No: 9844
  • 258 Thanks
  • 327 posts
  • Location: Iowa

Posted April 12, 2017 - 01:11 AM

Yes i also thought they were welded closed but they are not take the bottom pin out and it will push back through the bottom then take to any hydraulic shop and spend $15 bucks and ask them to change out your seals Watch them as they do it and buy an extra set of seals so you can do it yourself next time Kinda scary how simple it is


  • DMAX and cchap45 have said thanks

#5 adolphsson09 OFFLINE  

adolphsson09
  • Senior Member
  • Member No: 9844
  • 258 Thanks
  • 327 posts
  • Location: Iowa

Posted April 12, 2017 - 01:13 AM

Oh yea and you also have to take ot the hydraulic line ports They just unscrew EASY EASY EASY


  • limebuzz said thank you

#6 coldone OFFLINE  

coldone

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 839
  • 1,651 Thanks
  • 1,679 posts
  • Location: Central NC

Posted April 12, 2017 - 05:37 AM

Unscrew the ports, remove the shackle from the rod. Push rod, piston, gland and all out the back end. Measure seals and backers and order from some place on line.


  • DMAX and cchap45 have said thanks

#7 DMAX ONLINE  

DMAX

    Addicted

  • Senior Member
  • Member No: 264
  • 287 Thanks
  • 111 posts
  • Location: Eighty Four, Pa

Posted April 12, 2017 - 08:22 AM

Here's one off a 14/16 three point hitch I took apart a while ago. It's a little bigger diameter but basically the same design I think. It might help show what you'll see when it's opened up.

Attached Thumbnails

  • image.jpeg

  • Alc, KennyP, cchap45 and 1 other said thanks

#8 cchap45 OFFLINE  

cchap45

    New Member

  • Member
  • Member No: 6595
  • 88 Thanks
  • 53 posts
  • Location: MN

Posted April 12, 2017 - 08:25 AM

thanks everyone!



#9 KBuzz OFFLINE  

KBuzz
  • Member
  • Member No: 77146
  • 81 Thanks
  • 40 posts
  • Location: Avella PA

Posted April 17, 2017 - 04:28 PM

Thanks DMAX, for taking the time to setup, take, and submit the pic, I was curious as well. 


  • DMAX said thank you




Top