Jump to content

Garden Tractors and Parts on eBay



Photo
For Sale

parting out cub cadet 102



  • Please log in to reply
31 replies to this topic

#1 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 25, 2017 - 09:03 PM

due to a bad burr on the hex key shaft i've decided to totally part it out has some nice goodies on it too plus i have a snow blade $150.00 for it and under carriage and a real good condition 42" mowing deck $200 firm for that but most of the parts are still on tractor still but has the following rear wheel weights.......hydro lift assembly....creeper gear..... rear sleeve hitch no pin .........head light kit...... rear fenders 2 sets and much more stuff all narrow frame stuff willing to ship most anything to the lower 48 I would do Canada but you will be responsible for paying any duty taxes

Attached Thumbnails

  • GEDV0001.JPG
  • GEDV0027.JPG
  • GEDV0028.JPG
  • GEDV0023.JPG
  • GEDV0019.JPG
  • GEDV0020.JPG
  • GEDV0017.JPG
  • GEDV0016.JPG
  • GEDV0011.JPG

Edited by TravelinJavelin, January 25, 2017 - 09:05 PM.


#2 eodcoduto OFFLINE  

eodcoduto
  • Member
  • Member No: 65035
  • 30 Thanks
  • 23 posts
  • Location: Twentynine Palms, California

Posted January 25, 2017 - 09:25 PM

What do you want for the creeper gear?  Id love the rear too but shipping would kill me. 


  • TravelinJavelin said thank you

#3 diesel nut ONLINE  

diesel nut
  • Senior Member
  • Member No: 7572
  • 644 Thanks
  • 401 posts
  • Location: Templeton, MA

Posted January 25, 2017 - 09:39 PM

How much for the seat and reflectors on the fenders?


  • TravelinJavelin said thank you

#4 EricFromPa ONLINE  

EricFromPa

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 2135
  • 3,228 Thanks
  • 2,913 posts
  • Location: Bedford County Pa.

Posted January 26, 2017 - 12:07 AM

Doesn't cost much to have a crank welded up,turned down and a new keyway cut.Betting it would be around $50-60 tops.Would be a real shame to part out such a nice machine.Once it's gone it's gone forever.They will never make another tractor like those.

 

If you was a little closer I would take the whole tractor.CC 102 is by far my favorite tractor.


  • Bolens 1000, backwoods and Sawdust have said thanks

#5 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 26, 2017 - 05:46 AM

well in my neck of the woods the 102 the 125 and 122's are very plentiful up here...........I had a guy I know that has a machine shop look at it briefly quoted me $150 plus so not going to bother that's what i'm going to ask for the whole engine



#6 backwoods OFFLINE  

backwoods
  • Senior Member
  • Member No: 8613
  • 2,574 Thanks
  • 2,791 posts
  • Location: beaver dams new york

Posted January 26, 2017 - 07:22 AM

there hard to find here in my area that clean i see a few parts id love also would love the whole tractor unfortunately i dont have the extra right now im willing to help with trasport though for some one if the cover my gas


  • limebuzz said thank you

#7 nitro OFFLINE  

nitro
  • Senior Member
  • Member No: 71342
  • 170 Thanks
  • 113 posts
  • Location: New Castle PA

Posted January 26, 2017 - 10:41 AM

http://www.ebay.com/...akAAOSw2xRYhLww

Edited by nitro, January 26, 2017 - 12:06 PM.


#8 EricFromPa ONLINE  

EricFromPa

    Tractorholic

  • Senior Member
  • Contributor
  • Member No: 2135
  • 3,228 Thanks
  • 2,913 posts
  • Location: Bedford County Pa.

Posted January 26, 2017 - 03:00 PM

Good price but would have to have that crank turned down @ nitro.The Cub cranks are 1". But Still I could chuck it up in the lathe,turn it down and cut the keyway on the mill easily enough.Only takes a couple minutes on the lathe and maybe 10 minutes to setup and cut the keyway.

 

Don't know why they quoted him $150+ unless they would pull the engine out of the tractor,pull the crank,machine it and put it back together.Then I could see paying that much.Takes a good bit of time to tear an engine apart and re-assemble.

 

Having it tore down that far I think I would have it rebuilt anyway and more machining might be needed.Still a shame to part it out.


  • nitro said thank you

#9 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 26, 2017 - 06:02 PM

hey nitro i looked at that one on ebay and i wasn't sure if that was to new or not so i skipped over it



#10 nitro OFFLINE  

nitro
  • Senior Member
  • Member No: 71342
  • 170 Thanks
  • 113 posts
  • Location: New Castle PA

Posted January 26, 2017 - 06:57 PM

hey nitro i looked at that one on ebay and i wasn't sure if that was to new or not so i skipped over it

It was the first one I saw, might not b the right one but they are not hard to find.  There is a k301 down the road from me for $150.



#11 GTpicker01 OFFLINE  

GTpicker01

    GT Addict

  • Senior Member
  • -GTt Supporter-
  • Member No: 42575
  • 658 Thanks
  • 566 posts
  • Location: Pennsylvania

Posted January 27, 2017 - 02:34 PM

How much for the hydraulics & lighting system?



#12 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 28, 2017 - 12:30 PM

lights and tail light and switch have been sold



#13 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 28, 2017 - 05:36 PM

more 102 parts fuel tank very good condition inside is clean as a whistle blown out all through with compressed air no grime or varnish $50.00 firm!  Hydro system have confirmed system does work good ther was some weepage i noticed no real leaks the rubber hydro lines were recently replaced at some point the only things wrong that i found was it will need a arm return spring pushing it forward doesn't come back but if you pull back it springs right back and the pulley does have a wobble not sure why...could be just the set screw the cylinder rod has no pitting no leaks coming from it looking for $300 o/b/o......what ever is offered figure shipping on top.......... starter generator turns nicely not sure if it charges looking for $35.00 plus shipping 25lb wheel weights nice shape $100 plus shipping cub cadet 102 hood $50.00u  plus shipping real good shape no dents narrow frame mules drives pulleys turn very freely no squeaks $40.00 a set of rear fenders $25.00 2 front PTO's one is rebuilt the other is a core looking for $100 .00 for both......will have more parts off as time goes on the seat and rear fender reflectors are pending at this moment

Attached Thumbnails

  • GEDV0001 (1).JPG
  • GEDV0002.JPG
  • GEDV0006.JPG
  • GEDV0007.JPG
  • GEDV0008.JPG
  • GEDV0009.JPG
  • GEDV0012.JPG
  • GEDV0010.JPG
  • GEDV0003.JPG
  • GEDV0004.JPG


#14 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted January 31, 2017 - 05:58 PM

hydro pump has been sold and starter generator



#15 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 114 Thanks
  • 193 posts
  • Location: Maine

Posted February 03, 2017 - 05:16 AM

seat and reflectors and wheel weights now have been sold


Edited by TravelinJavelin, February 03, 2017 - 05:18 AM.






Also tagged with one or more of these keywords: for sale

Top