Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

the eliminator 1900 does it have the cast iron fornt end?


  • Please log in to reply
6 replies to this topic

#1 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 98 Thanks
  • 182 posts
  • Location: Maine

Posted November 27, 2016 - 06:28 PM

I have been on a search for a roller of a qs or a qt but have noticed the frame is similar on the eliminator 1900 series and thinking possibly grabbing has a bad motor also have a question on tranny to is it a H/L range? or is this a big motored XL series?



#2 blackjackjakexxix OFFLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Member No: 2194
  • 2,734 Thanks
  • 1,994 posts
  • Location: Pulaski,Pa 16143

Posted November 27, 2016 - 07:02 PM

Can't remember for sure about the 2 speed rearend,but I don't think so,these are a heavier built machine than the XL,cast front axle

#3 Cvans OFFLINE  

Cvans

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Member No: 5412
  • 5,775 Thanks
  • 5,736 posts
  • Location: Eastern SD.

Posted November 27, 2016 - 07:35 PM

If I remember correctly my Son's is an eliminator and it is a single speed. 



#4 Zekkjacen OFFLINE  

Zekkjacen
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 38932
  • 144 Thanks
  • 187 posts
  • Location: Waynesburg, Ohio

Posted November 27, 2016 - 08:15 PM

I have seen Eliminators with hi/lo rear ends, but I believe they were a special order on the lower models.  My uncle had a 1400 with low range, but I have only seen his and another one with it.  All others I've seen were single-speed.



#5 TravelinJavelin OFFLINE  

TravelinJavelin
  • Senior Member
  • Member No: 84768
  • 98 Thanks
  • 182 posts
  • Location: Maine

Posted November 27, 2016 - 08:49 PM

hey thanks guys appreciate the info!



#6 blackjackjakexxix OFFLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Member No: 2194
  • 2,734 Thanks
  • 1,994 posts
  • Location: Pulaski,Pa 16143

Posted November 27, 2016 - 10:58 PM

1400 was a gear drive with low range,the 1900 was a hydro
  • ClassicBolens said thank you

#7 ClassicBolens OFFLINE  

ClassicBolens
  • Senior Member
  • Contributor
  • Member No: 48806
  • 1,350 Thanks
  • 489 posts
  • Location: IN

Posted November 28, 2016 - 03:42 PM

Yes the 1900 has the cast iron front end/ axle assembly. No HI/LO range though. That was only offered on the 20 HP tractors such as the 2000 (5020H) and later GT2000 Duratrac (5120H).

The next question is which model 1900 is it? The early 1900 is a QT series model 1966. The later 1900 is a 5000 series model 5019H. Neither are the same as XL-Medium Frames.

Edited by ClassicBolens, November 28, 2016 - 03:51 PM.

  • blackjackjakexxix and Zekkjacen have said thanks




Top