Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Ebay, need quick answer Batt holder


  • Please log in to reply
5 replies to this topic

#1 glgrumpy ONLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 6,647 Thanks
  • 6,460 posts
  • Location: Huntington, IN 46750 North East in State

Posted October 09, 2016 - 09:40 AM

Have my G14. Never paid much attention to the battery or try in it, might have to go out and look again. Thinking just flat metal by dash?  Anyway, on epay is a couple of battery holders. They have the rods to tighten down, but are real wide Metal? or Plastic? not sure to kinda wrap battery. Do the ends just kinda  catch the top edge of battery then?  don't see anything going across for the top. These work?  I did not find in parts book till the last page of electric circuits and looks like it was for the later model tractor??  Would have to dig up my number again, but think is the later one.  This anything worth having or is there better way to hold it. Will be long time before I need, but just like to be ready to fix up "something" to use there.


  • Bolens800uk said thank you

#2 Cat385B ONLINE  

Cat385B

    Therapy CAT

  • Senior Member
  • Contributor
  • Member No: 8002
  • 11,691 Thanks
  • 8,886 posts
  • Location: MN

Posted October 09, 2016 - 09:52 AM

Here's the quick answer that does you absolutely no good, but I delivered it really fast.

How the heck should I know?

You're welcome!

Edited by Cat385B, October 09, 2016 - 09:52 AM.

  • KC9KAS, HANKG and Bolens800uk have said thanks

#3 MrMarty51 OFFLINE  

MrMarty51
  • Senior Member
  • Member No: 62893
  • 141 Thanks
  • 105 posts
  • Location: Miles City, Montana

Posted October 09, 2016 - 09:57 AM

I went to John Deere, asked about the battery hold down for My 110, they have them, comes with the J-bolts and the cover that the J-bolts hooks into. FREE for the asking.

I couldn`t believe it until it finally arrived and yes, it was free.


  • Bolens800uk said thank you

#4 stiemmy ONLINE  

stiemmy
  • Senior Member
  • Contributor
  • Member No: 53712
  • 1,288 Thanks
  • 1,094 posts
  • Location: Freekin cold central WI

Posted October 09, 2016 - 10:16 AM

Here's the quick answer that does you absolutely no good, but I delivered it really fast.
How the heck should I know?
You're welcome!


LMAO!!!!!!

#5 WrenchinOnIt OFFLINE  

WrenchinOnIt
  • Senior Member
  • -GTt Supporter-
  • Member No: 8592
  • 2,514 Thanks
  • 732 posts

Posted October 09, 2016 - 02:14 PM

These are the correct ones, kinda of PITA , BUT they do the best job IF ,your battery is correct size dimensionally.
http://www.ebay.com/...IkAAOSwNRdX7K1g

I'd check with our site sponsors also, Bolens 1000 " Bolens Parts and Supplies" ,Blackjackjakexxix "Rick's Bolens Tractor parts or bhts "Bob's Lawn and Garden Tractors. May treat you better.

Sorry didn't read your post thoroughly, if these are what your referencing they are metal , they catch the bottom of the battery on the sides and as you tighten them down they wedge between the sides of the dash tower and the battery case holding it tight.

Attached Thumbnails

  • IMG_20161009_1512359_rewind_kindlephoto-60596976.jpg

Edited by WrenchinOnIt, October 09, 2016 - 05:36 PM.

  • Bolens 1000, Bruce Dorsi and 29 Chev have said thanks

#6 Bolens 1000 ONLINE  

Bolens 1000

    DR. Bolens

  • Staff Admin
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 7
  • 12,671 Thanks
  • 17,198 posts
  • Location: Western NY

Posted October 09, 2016 - 03:18 PM

:ditto:  Wrenchinonit is correct, dont know the number off hand but his pic shows orginal way to secure it as well as the OEM size battery they used. Had one of those style last me almost 12 years before she started leaking acid and I had to get rid of it.

 

 

If you want to run the little L&G batteries I found these mounts to work very good.  (see pic 4)

 

http://bolenspartsan...ely-wheelhorse/






Top