Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Clutch material bake.


  • Please log in to reply
5 replies to this topic

#1 glgrumpy OFFLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 6,647 Thanks
  • 6,460 posts
  • Location: Huntington, IN 46750 North East in State

Posted August 14, 2016 - 03:17 PM

G14 clutch, baking at 350 now. Says 4hrs. Not getting any smell as warned. Zat mean not working? The Boughton brake had glue oozing out of it. That supposed to happen here? Not getting that.
  • Sawdust said thank you

#2 glgrumpy OFFLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 6,647 Thanks
  • 6,460 posts
  • Location: Huntington, IN 46750 North East in State

Posted August 14, 2016 - 06:34 PM

Well parts been out for 2 hrs and still plenty hot to touch. Will just leave till tomorrow before taking the bolt apart that is squeezing it all in. No ooz or smell!!



#3 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 28,355 Thanks
  • 39,630 posts
  • Location: Collinsville, Oklahoma

Posted August 14, 2016 - 06:39 PM

Mama should be happy for that!


  • WNYTractorTinkerer said thank you

#4 glgrumpy OFFLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 6,647 Thanks
  • 6,460 posts
  • Location: Huntington, IN 46750 North East in State

Posted August 15, 2016 - 06:07 PM

Well, pulled apart the bolted up assembly today. Seems the discs are on there OK. Very little oozing out of glue is shown, only couple of spots. SO, now to paint it up and try to figure out how it all goes back together again! I put the center assembly in frame now instead of trying to re-assemble while apart on bench. SO...gonna be laying under it, or over the tractor lift, or swearing at it in near future trying to get back in. Where's that parts drawing again.........get the manual!

Attached Thumbnails

  • 20160815_175742.jpg
  • 20160815_175715.jpg

Edited by glgrumpy, August 15, 2016 - 06:08 PM.


#5 Bud W OFFLINE  

Bud W

    New Member

  • Senior Member
  • Contributor
  • Member No: 2359
  • 228 Thanks
  • 217 posts
  • Location: Cly, Pennsylvania

Posted August 16, 2016 - 09:56 AM

How did you get the old lining off?



#6 glgrumpy OFFLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 6,647 Thanks
  • 6,460 posts
  • Location: Huntington, IN 46750 North East in State

Posted August 16, 2016 - 01:19 PM

Bud, one side was gone, metal not scored tho, not sure why. Other side was very thin for most of it. Once I got an edge started with a small chisel, it just kinda broke away in pieces leaving the thin layer behind. Scraped that a bit, wire wheel on the grinder head some, then final took to my sandblaster and cleaned whole thing up. Was kinda scary pushing out the needle bearing in center, but used press and it came out good.


  • Cvans said thank you




Top