Jump to content

Time to Vote for Tractor of the Month!
Garden Tractors and Parts on eBay



Photo
- - - - -

1855 mid pro disassembly help needed


  • Please log in to reply
10 replies to this topic

#1 Dayton_King OFFLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 742 Thanks
  • 777 posts
  • Location: Atlanta Georgia

Posted June 06, 2016 - 06:27 PM

Any advice on how to take this apart. I got one snap ring off and I bent the pulley trying to get it off.

#2 limebuzz ONLINE  

limebuzz

    Member

  • Senior Member
  • Member No: 795
  • 943 Thanks
  • 929 posts
  • Location: Bluevale Ontario

Posted June 06, 2016 - 08:04 PM

It's been awhile, but the end nuts have to come off.

#3 ducky OFFLINE  

ducky

    Senior Member

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 564
  • 1,943 Thanks
  • 4,067 posts
  • Location: Freedom, WI

Posted June 06, 2016 - 10:29 PM

The big nut contain the bearings that are held into the nuts with snap rings.  They unscrew RH thread.There are also snap ring on the shaft out side the nuts.  Best way is to get the rear nut unscrewed and off the shaft, then unscrew the front nut and the assemble should come out the front of the tractor.  Than you can get it in a press to complete disassembly.  There is a snap ring on the shaft behind the front nut that keep the shaft from floating forward with in use.

Here is the Manual



#4 Dayton_King OFFLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 742 Thanks
  • 777 posts
  • Location: Atlanta Georgia

Posted June 07, 2016 - 04:49 AM

I am slow with out coffee. RH threads are normal threads correct?

#5 ducky OFFLINE  

ducky

    Senior Member

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 564
  • 1,943 Thanks
  • 4,067 posts
  • Location: Freedom, WI

Posted June 07, 2016 - 07:04 AM

I am slow with out coffee. RH threads are normal threads correct?

You got it.



#6 Dayton_King OFFLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 742 Thanks
  • 777 posts
  • Location: Atlanta Georgia

Posted June 07, 2016 - 07:56 AM

I think I need to get a 10ft breaker bar, or gain some weight lol

#7 adolphsson09 OFFLINE  

adolphsson09
  • Senior Member
  • Member No: 9844
  • 258 Thanks
  • 327 posts
  • Location: Iowa

Posted June 07, 2016 - 10:26 AM

Take what apart i dont see any pictures


  • Dayton_King said thank you

#8 Dayton_King OFFLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 742 Thanks
  • 777 posts
  • Location: Atlanta Georgia

Posted June 07, 2016 - 07:32 PM

Pics lol

Attached Thumbnails

  • 20160605_112314.jpg
  • 20160605_112322.jpg


#9 ducky OFFLINE  

ducky

    Senior Member

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 564
  • 1,943 Thanks
  • 4,067 posts
  • Location: Freedom, WI

Posted June 07, 2016 - 09:23 PM

I think I need to get a 10ft breaker bar, or gain some weight lol

They are big but not that tight unless rusted bad.



#10 adolphsson09 OFFLINE  

adolphsson09
  • Senior Member
  • Member No: 9844
  • 258 Thanks
  • 327 posts
  • Location: Iowa

Posted June 07, 2016 - 09:52 PM

You may get lucky and find a pulley from someone or on ebay if not i believe i paid close to $85 for the pulley plus shipping which put it close to around $100 just for the pulley i bought through partstree someone should have warned you about that pulley on putting some panther pee on it and letting it soak for a day or so and maybe some heat beforehand I did the same thing once and it was an expensive lesson



#11 Dayton_King OFFLINE  

Dayton_King
  • Senior Member
  • Member No: 68926
  • 742 Thanks
  • 777 posts
  • Location: Atlanta Georgia

Posted June 08, 2016 - 05:04 AM

I sold the pto. He doesn't want the pulley. I will try again tonight




Top