Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Throttle linkage for Wisconsin engine connection

wisconsin engine throttle linkage

  • Please log in to reply
6 replies to this topic

#1 redoak3 OFFLINE  

redoak3
  • Member
  • Member No: 75384
  • 12 Thanks
  • 11 posts
  • Location: Nebraska

Posted April 11, 2016 - 05:55 PM

Can someone post a picture of what the throttle linkage connection is supposed to look like on a 1958 Economy with a Wisconsin AENL engine?  The picture shows what I have now (minus the throttle cable).  I'm guessing that it is some sort of toggle bracket.

 

Also a picture of the choke cable mounting would be appreciated.

Attached Thumbnails

  • 20160410_195402.jpg


#2 DougT ONLINE  

DougT

    Dog Approved

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 584
  • 5,736 Thanks
  • 4,290 posts
  • Location: north central Ohio

Posted April 11, 2016 - 07:32 PM

I think the part that goes there is a Wisconsin part. Did you check out this manual?  http://gardentractor...n-parts-manual/


  • redoak3 said thank you

#3 redoak3 OFFLINE  

redoak3
  • Member
  • Member No: 75384
  • 12 Thanks
  • 11 posts
  • Location: Nebraska

Posted April 12, 2016 - 05:13 PM

I think the part that goes there is a Wisconsin part. Did you check out this manual?  http://gardentractor...n-parts-manual/

 

Thanks, I did check out the Wisconsin engine manual, but the pictorial in the manual looks like it is for a stationary engine application rather than connection to a conduit cable.



#4 Bolens 1000 OFFLINE  

Bolens 1000

    DR. Bolens

  • Staff Admin
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 7
  • 12,703 Thanks
  • 17,209 posts
  • Location: Western NY

Posted April 12, 2016 - 05:20 PM

The Bolens Ridemasters used a block the cable threaded into, each manufacture likely had their own unique design the engines bought from Wisconsin direct would have had the stationary setup shown in the manual.

 

 

546.jpg


  • Alc and redoak3 have said thanks

#5 DougT ONLINE  

DougT

    Dog Approved

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 584
  • 5,736 Thanks
  • 4,290 posts
  • Location: north central Ohio

Posted April 12, 2016 - 06:18 PM

I've seen a bunch that used the stationary lever as a bellcrank and hooked the cable into it.


  • Bolens 1000 and redoak3 have said thanks

#6 redoak3 OFFLINE  

redoak3
  • Member
  • Member No: 75384
  • 12 Thanks
  • 11 posts
  • Location: Nebraska

Posted April 17, 2016 - 10:36 AM

I've seen a bunch that used the stationary lever as a bellcrank and hooked the cable into it.

 

Yes, I have seen this also but I don't recall how the cable conduit attached.  A picture of how the Economy was set up would be helpful and appreciated.



#7 MNGB ONLINE  

MNGB
  • Senior Member
  • Member No: 62466
  • 1,020 Thanks
  • 840 posts
  • Location: Minnesota

Posted April 17, 2016 - 11:27 AM

Hi redoak3, you could join the Yahoo Power king group and ask there, lot more members there with Wis powered tractors there. I looked thur some of the photo albums but its large and takes lots of time to look thur all of them.







Also tagged with one or more of these keywords: wisconsin engine, throttle, linkage

Top