Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

1886 and HT 3pt


  • Please log in to reply
16 replies to this topic

#1 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted April 06, 2016 - 09:49 AM

I am looking into getting a 3pt hooked up for my ht20
Just wondering what the difference are between it and the 1886

Thanks.

#2 LPBolens ONLINE  

LPBolens

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 874
  • 1,176 Thanks
  • 882 posts
  • Location: North Central Illinois

Posted April 06, 2016 - 10:43 AM

The HT style 3-pt requires the frame rail extension past the rear axle. That extension is where the pivot blocks for the cross shaft are installed. If a Large Frame tractor does not have the frame extensions, you have to use the lighter-duty 3-pt that was offered for the early Large Frames like the 1250, 1455, etc.


  • blackjackjakexxix and AA Hayes have said thanks

#3 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted April 06, 2016 - 11:19 AM

So basically, an 1886 3 pt would work on my ht20 as I don't have frame rail extensions?
And pictures of the frame rail extensions?

#4 Husky ONLINE  

Husky

    Member

  • Senior Member
  • Contributor
  • Member No: 63
  • 922 Thanks
  • 892 posts

Posted April 06, 2016 - 12:00 PM

I've got manuals for both the 1886 style p/n 18010 and the HT style p/n 18086. Here's a picture of my 1886 3pt hitch. It uses push rods whereas the HT style uses a single lift lever and is set up different. I don't think the 18010 would work on the HT series. Also a picture from the parts list of the 18086 so you can see the difference between the two.

Attached Thumbnails

  • DSC06154.JPG
  • DSC06158a.jpg
  • DSC06159.JPG
  • 18086.jpg

Edited by Husky, April 06, 2016 - 12:02 PM.

  • blackjackjakexxix, AA Hayes and Paulgo have said thanks

#5 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted April 06, 2016 - 12:41 PM

Thank you!

#6 blackjackjakexxix ONLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Sponsor
  • Member No: 2194
  • 2,345 Thanks
  • 1,754 posts
  • Location: Pulaski,Pa 16143

Posted April 06, 2016 - 01:44 PM

I believe what LPBolens was saying is the HT-20 had longer frame rails in the back then the 1886 ,they stick out past the rearend more than on the 86's


  • LPBolens and AA Hayes have said thanks

#7 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted April 06, 2016 - 03:07 PM

Makes sense!

Edited by AA Hayes, April 06, 2016 - 03:08 PM.


#8 wilberj ONLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,179 Thanks
  • 5,205 posts
  • Location: Michigan

Posted April 06, 2016 - 04:14 PM

The 1886s-05 and the HT18/1886s-06 also uses the same 3 point as on the HT20.  Anything older then the 1886-04 uses the older 3 point.  


  • LPBolens, ClassicBolens and AA Hayes have said thanks

#9 blackjackjakexxix ONLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Sponsor
  • Member No: 2194
  • 2,345 Thanks
  • 1,754 posts
  • Location: Pulaski,Pa 16143

Posted April 06, 2016 - 04:19 PM

Yep,forgot about the late 86's having the longer frame rails
  • AA Hayes said thank you

#10 LPBolens ONLINE  

LPBolens

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 874
  • 1,176 Thanks
  • 882 posts
  • Location: North Central Illinois

Posted April 06, 2016 - 04:44 PM

I cannot tell you whether you could install the earlier 18010 3-pt on an HT20. Although I have both types of 3-pt hitches, it never occurred to me to try to.


  • blackjackjakexxix said thank you

#11 OldBuzzard ONLINE  

OldBuzzard

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 805
  • 6,481 Thanks
  • 4,633 posts
  • Location: Oberlin, OH

Posted April 06, 2016 - 07:08 PM

Not too long ago someone posted pics of the early 3-PT hitch being used on one of the HT series.

 

I forget if it was here, MTF, or one of the Facebook pages.


Edited by OldBuzzard, April 06, 2016 - 07:08 PM.

  • blackjackjakexxix and AA Hayes have said thanks

#12 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted April 06, 2016 - 08:38 PM

I'm not on Facebook but I will check out here and mtf. Thanks.

#13 NJKen OFFLINE  

NJKen
  • Senior Member
  • Member No: 9515
  • 1,359 Thanks
  • 1,284 posts
  • Location: New Jersey

Posted May 08, 2016 - 05:03 AM

Not too long ago someone posted pics of the early 3-PT hitch being used on one of the HT series.

I forget if it was here, MTF, or one of the Facebook pages.


I didn't post any pics but I did use the early style on one of my HT20's. So they will work.
  • wilberj and AA Hayes have said thanks

#14 wilberj ONLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,179 Thanks
  • 5,205 posts
  • Location: Michigan

Posted May 08, 2016 - 08:35 AM

I didn't post any pics but I did use the early style on one of my HT20's. So they will work.

 

Wow were you been!



#15 NJKen OFFLINE  

NJKen
  • Senior Member
  • Member No: 9515
  • 1,359 Thanks
  • 1,284 posts
  • Location: New Jersey

Posted May 08, 2016 - 10:21 AM

Wow were you been!


Berry Berry busy. 😝
  • wilberj said thank you




Top