Jump to content

Time to Vote for Tractor of the Month!
Garden Tractors and Parts on eBay



Photo
- - - - -

Re: Tiller and shaft 1050, H16


  • Please log in to reply
7 replies to this topic

#1 Tspeyfly OFFLINE  

Tspeyfly
  • Member
  • Member No: 60304
  • 9 Thanks
  • 16 posts
  • Location: Oregon

Posted March 28, 2016 - 11:53 AM

Hello everyone

Does anyone know if the tiller off a 1050 will fit a H16. shaft?

Thank 's,

Thomas

P.S. Is there a tutorial for changing out the PTO belts on a 1050?



#2 chieffan ONLINE  

chieffan
  • Senior Member
  • Contributor
  • Member No: 62695
  • 7,521 Thanks
  • 5,315 posts
  • Location: SW Iowa

Posted March 28, 2016 - 12:31 PM

I use one that I had on a 1050 and now on an H12.  Only difference between the H series is the engine.  All tube frames.


  • Tspeyfly said thank you

#3 Bolens 1000 ONLINE  

Bolens 1000

    DR. Bolens

  • Staff Admin
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 7
  • 13,717 Thanks
  • 17,630 posts
  • Location: Western NY

Posted March 28, 2016 - 12:41 PM

That tiller should bolt right up without issue

 

For the PTO belts you will have to remove the drive belts off the engine sheave to slide the old ones off and install the new ones.

The PTO assembly is held on by 3 bolts , loosen those to give you slack and then remove the bolts from the belt guide that should give enough wiggle room to do your belt installation


  • blackjackjakexxix and Tspeyfly have said thanks

#4 29 Chev ONLINE  

29 Chev

    A Little Off Plumb

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 63590
  • 5,943 Thanks
  • 1,969 posts
  • Location: Ontario Canada

Posted March 28, 2016 - 03:01 PM

Here is the belt replacement and tensioning procedure from the owners manual in PDF format.  

Attached Files


  • blackjackjakexxix and Tspeyfly have said thanks

#5 wilberj OFFLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,576 Thanks
  • 5,394 posts
  • Location: Michigan

Posted March 28, 2016 - 03:18 PM

I use one that I had on a 1050 and now on an H12.  Only difference between the H series is the engine.  All tube frames.

 

H12 gotta be rare!  :wave:  :poke:


  • Tspeyfly said thank you

#6 chieffan ONLINE  

chieffan
  • Senior Member
  • Contributor
  • Member No: 62695
  • 7,521 Thanks
  • 5,315 posts
  • Location: SW Iowa

Posted March 28, 2016 - 06:50 PM

H12 gotta be rare!  :wave:  :poke:

Sure does.  I meant G12 with a 14 hp Tech, does that make it a G14?  Thanks for the heads up.



#7 wilberj OFFLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,576 Thanks
  • 5,394 posts
  • Location: Michigan

Posted March 28, 2016 - 06:55 PM

Sure does.  I meant G12 with a 14 hp Tech, does that make it a G14?  Thanks for the heads up.

 

If it has not been replaced It would be a G14.



#8 chieffan ONLINE  

chieffan
  • Senior Member
  • Contributor
  • Member No: 62695
  • 7,521 Thanks
  • 5,315 posts
  • Location: SW Iowa

Posted March 28, 2016 - 08:39 PM

G12 with a bad motor.  Put a 14 in I had from another project.  Maybe a G13??






Top