Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

Panzer T70 Resto-Mod

Started by BowDown , Mar 07, 2016 08:05 PM

  • Please log in to reply
317 replies to this topic

#46 Chris11 OFFLINE  

Chris11

    old Member

  • Senior Member
  • Member No: 1601
  • 1,687 Thanks
  • 976 posts
  • Location: Hudson Mass

Posted May 12, 2016 - 05:55 AM

There's one bearing on that shaft inside. You will have to support the end.
  • BowDown said thank you

#47 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 12, 2016 - 06:19 AM

One would imagine there was a bushing or something off the original engine that supported it?


Sent from my iPhone using Tapatalk

#48 jdcrawler OFFLINE  

jdcrawler

    tinkerer

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 1639
  • 4,197 Thanks
  • 1,917 posts
  • Location: Madison, Indiana

Posted May 12, 2016 - 08:12 AM

One would imagine there was a bushing or something off the original engine that supported it?


Sent from my iPhone using Tapatalk

 

Yes.

 

The input shaft on standard transmissions are supported by a bronze bushing in the center of the engine's crankshaft.


Edited by jdcrawler, May 12, 2016 - 08:14 AM.

  • BowDown said thank you

#49 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 12, 2016 - 01:16 PM

Worked on the trans mounts a bit more. Should work out rather well.


Sent from my iPhone using Tapatalk

#50 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 12, 2016 - 01:17 PM

1e991754d57f0a694313f29545660fce.jpg082082f4cba87f9efa8429c19633b1db.jpgb92aba8eaeb0de213cacd60db51c9760.jpg


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#51 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 15, 2016 - 06:44 PM

Got a couple hours today to play. Tacked the front and rear mount down. Tacked the motor plate down. Marked where I need to cut and also cut the start of my shim blocks for the front grill mounts.

Looks like minimal work this week but may have a whole Sunday next week to knock this out!


Sent from my iPhone using Tapatalk
  • Chris11 said thank you

#52 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 15, 2016 - 06:45 PM

0a676ee4ed947347e3bfc63d722587c6.jpg9c74cdc22446b2241d3bb1f4f198e0e0.jpgab3a81b6a1b2c6132ec7f388076b0507.jpg8fe05668f395b811f0fbe5035693fc90.jpg


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#53 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 16, 2016 - 01:27 PM

Holy crap milling takes forever. Lol. 45min for 2 3/4" deep 1-3/4" diameter relief cuts.


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#54 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 16, 2016 - 01:28 PM

f0045a5737a9ea535736895d989b1d6b.jpg65813052093e5fad5b790b69e8ad814e.jpg


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#55 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 18, 2016 - 01:28 PM

Finished machining out the nut reliefs on the bottom and cut the stud passthrough holes in the top. Will use acorn nuts to secure the blocks down, but first I need to install longer studs. The grill with then get mocked up and 1/2" studs installed into the blocks.


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#56 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 18, 2016 - 01:29 PM

b68044f02f796bdadab1a10198e9d729.jpgc42386345df5566dce32ecfca86e921a.jpg


Sent from my iPhone using Tapatalk
  • Chris11 and Traill95 have said thanks

#57 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 22, 2016 - 07:16 PM

Split up my Sunday between car audio and tractor. Finished milling the spacer blocks and welded in some 1/2bolts as mounting studs. Grill mounting is almost complete just need to install longer front axle studs.


Sent from my iPhone using Tapatalk

#58 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted May 22, 2016 - 07:17 PM

f3f7bbf09cac90380747240289337c3f.jpg71f4db1768fa1bce5a4b0a1527ae8fc6.jpg5788c68d2dcef012c51d931c1e3b991f.jpg


Sent from my iPhone using Tapatalk

#59 BowDown OFFLINE  

BowDown
  • Senior Member
  • Member No: 10128
  • 551 Thanks
  • 562 posts
  • Location: Central, NY

Posted November 13, 2016 - 06:38 PM

Getting close to firing the motor. I will be this week. I just got back to this project after finishing up my car audio nationals run.

Motor is bolted down. Changed oil, filter, plugs and have begun wiring.

I also redid the grill mounting. Didn't like the spacer look in the front. Really hope this motor runs. 4adb6afc852d81104b79706c664fdd0f.jpg9b87784ed66a6ba24a51a69ae3a19d70.jpgd0bcd8891dd7e83fa89dbaa0f3403c3b.jpg5e065aa7a4dd2ddd15fe53cd545cd9da.jpg


Sent from my iPhone using Tapatalk

#60 Cat385B OFFLINE  

Cat385B

    HAZMAT CAT

  • Senior Member
  • Contributor
  • Member No: 8002
  • 14,370 Thanks
  • 10,142 posts
  • Location: MN

Posted November 13, 2016 - 07:11 PM

How'd you do at Nationals?
Back to Copar, Pennsylvania Panzer Tractor Forum


  1. GTtalk
  2. → Barn
  3. → Lawn & Garden Tractors by Make
  4. → Copar, Pennsylvania Panzer Tractor Forum
  5. Privacy Policy
  6. Site Guidelines ·
Top