Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Terra-blade


  • Please log in to reply
6 replies to this topic

#1 HT20D OFFLINE  

HT20D
  • Member
  • Member No: 75535
  • 31 Thanks
  • 16 posts
  • Location: Maine

Posted February 11, 2016 - 05:45 PM

I've had a few people ask about pictures and dimensions for the Terra-blade. This is off my bolens large frame.

Everything is 1/4" thick.

Hopefully the drawings are clear enough. No computer at home, just a printer/scanner hooked wirelessly to my smart phone so bear with me.

If there's any specific picture you'd like to see, let me know and I'll post them within a couple days. I'll get some close ups of it on the tractor in the next couple weeks. It's off the tractor now.

Attached Thumbnails

  • IMG_20160211_164520116.jpg
  • IMG_20160211_164513752.jpg
  • IMG_20160211_164256293.jpg
  • IMG_20160211_164245568.jpg
  • IMG_20160211_164212936.jpg
  • IMG_20160211_164157352.jpg
  • IMG_20160211_164131806.jpg
  • IMG_20160211_164009870.jpg
  • IMG_20160211_163957139.jpg
  • IMG_20160211_163820700.jpg
  • IMG_20160211_163803755.jpg
  • IMG_20160211_163740392.jpg
  • IMG_20160211_163727829.jpg
  • EPSON012.jpg
  • EPSON010.jpg
  • EPSON007.jpg

Edited by HT20D, February 11, 2016 - 06:28 PM.

  • OldBuzzard, LPBolens, Texas Deere and Horse and 11 others have said thanks

#2 LPBolens ONLINE  

LPBolens

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 874
  • 1,176 Thanks
  • 882 posts
  • Location: North Central Illinois

Posted February 12, 2016 - 01:46 AM

If I can find an appropriate blade, that should be relatively easy to fab up. If I put a hydraulic ram on it, I can adjust the angle using the rear ports on one of the later Large Frames.

 

Thanks, HT20D!


  • HT20D said thank you

#3 AA Hayes OFFLINE  

AA Hayes
  • Senior Member
  • -GTt Supporter-
  • Member No: 67383
  • 324 Thanks
  • 274 posts
  • Location: Ontario Canada

Posted February 12, 2016 - 06:55 AM

Once I get some time I will be fabbing one of these. I have a 10' length of a cutting edge from a highway snow plow, it is not curved but I think with its weight and thickness would do a fine job.

#4 teapot OFFLINE  

teapot

    New Member

  • Member
  • Member No: 2138
  • 4 Thanks
  • 9 posts

Posted March 22, 2016 - 04:07 PM

Thanks for posting information and drawings. Very helpful. I have two questions if you could answer. Is this for a LF Bolens and if it is does it mount to the frame underneath motor or on the steering bridge. And it's been awhile since I have read plans.What does FB stand for. Thanks again.

#5 WrenchinOnIt OFFLINE  

WrenchinOnIt
  • Senior Member
  • -GTt Supporter-
  • Member No: 8592
  • 2,515 Thanks
  • 732 posts

Posted March 22, 2016 - 04:44 PM

Thanks for posting information and drawings. Very helpful. I have two questions if you could answer. Is this for a LF Bolens and if it is does it mount to the frame underneath motor or on the steering bridge. And it's been awhile since I have read plans.What does FB stand for. Thanks again.


Looking at the pics I'd say FB stands for flat bar, RB round bar

Nice drawings HT20D
  • LPBolens and teapot have said thanks

#6 teapot OFFLINE  

teapot

    New Member

  • Member
  • Member No: 2138
  • 4 Thanks
  • 9 posts

Posted March 22, 2016 - 07:17 PM

Thanks. Must have been too involved in measuring that I wasn't thinking. Thanks

#7 HT20D OFFLINE  

HT20D
  • Member
  • Member No: 75535
  • 31 Thanks
  • 16 posts
  • Location: Maine

Posted March 26, 2016 - 04:31 AM

Looking at the pics I'd say FB stands for flat bar, RB round bar
Nice drawings HT20D


You are correct, FB= flat bar, RB= round bar.

Thank you, I am a structural designer so this was right up my alley. I would have liked to do this in the 3D software I use at work...or at least AutoCAD but with no computer at home, it was back to pen and paper.
  • LPBolens, teapot and KennyP have said thanks




Top