Working on the bumper, almost the same as Hulk II. It looks like 2 months to build up tire funds, but my Grandson wants me to start on the JD-165 soon. Trying to stay off credit.
2 votes
Brother of Hulk II
Started by
larrybl
, Jan 31, 2016 04:59 PM
489 replies to this topic
#346
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 12, 2016 - 08:42 PM
- KennyP said thank you
#347
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 13, 2016 - 08:46 PM
Installed the bumper, trying to convince the banker we don't need so much in the savings account.
Attached Thumbnails
- KennyP said thank you
#348
OFFLINE
Cat385B
-
- Senior Member
- Contributor
- Member No: 8002
- 12,885 Thanks
- 9,480 posts
Therapy CAT
- Location: MN
Posted June 13, 2016 - 09:22 PM
With the jack stand underneath it, have you considered that machine needs red pinstripes?
- larrybl said thank you
#349
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 13, 2016 - 09:25 PM
With the jack stand underneath it, have you considered that machine needs red pinstripes?
It will be un-badged like the others unless someone comes up with a decal set for the Craftsman II series.
#350
OFFLINE
bbuckler
-
- Senior Member
- Member No: 59269
- 2,765 Thanks
- 2,440 posts
- Location: Killeen,Tx
Posted June 13, 2016 - 10:13 PM
It will be un-badged like the others unless someone comes up with a decal set for the Craftsman II series.
I actually had a friend buy a set for one
- larrybl said thank you
#351
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 14, 2016 - 08:57 PM
I actually had a friend buy a set for one
Where?
#352
OFFLINE
bbuckler
-
- Senior Member
- Member No: 59269
- 2,765 Thanks
- 2,440 posts
- Location: Killeen,Tx
Posted June 14, 2016 - 09:03 PM
- larrybl said thank you
#353
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 14, 2016 - 09:05 PM
Front end alignment. I put the rims on and it wasn't looking quite right. I tightened the lugs on the rear rims and ran a string around the rims. It was telling, Then I started adjusting and found the tie rod ends had different thread counts (one was barely attached). So I started there and got the tie rods threads at 3/4" then adjusted equally till the string showed alignment. I had to re-set the steering wheel 3 notches to center it. All looks good now.
Attached Thumbnails
- KennyP, Sawdust, Phluphy and 1 other said thanks
#354
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 14, 2016 - 09:09 PM
Tires first! I book marked it, I need 2 sets and $300 is a little out of the scope right now.
- Sawdust said thank you
#355
OFFLINE
TAHOE
-
- Senior Member
- Contributor
- Member No: 24522
- 7,526 Thanks
- 5,462 posts
- Location: "Hamiltucky" Ohio
Posted June 15, 2016 - 08:29 AM
Front end alignment. I put the rims on and it wasn't looking quite right. I tightened the lugs on the rear rims and ran a string around the rims. It was telling, Then I started adjusting and found the tie rod ends had different thread counts (one was barely attached). So I started there and got the tie rods threads at 3/4" then adjusted equally till the string showed alignment. I had to re-set the steering wheel 3 notches to center it. All looks good now.
that's pretty slick Larry!
- larrybl said thank you
#356
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 15, 2016 - 06:01 PM
Well, after some discussion with the Boss, I was allowed to purchase the tires and decals, Thanks Brandon for the link! I'll definitely be taking BOH to the October show in Temple.
- bbuckler said thank you
#357
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 15, 2016 - 07:20 PM
If anyone is interested, this is the decal package. Kinda pricy at $130.00 or so, but I couldn't find them before.
Attached Thumbnails
- MH81 said thank you
#358
ONLINE
KennyP
-
- Super Moderator
- Staff
- -GTt Supporter-
- Contributor
- Member No: 2253
- 33,717 Thanks
- 43,001 posts
FORDoholic
- Location: Collinsville, Oklahoma
Posted June 16, 2016 - 05:29 AM
On a computer that died, I had a drawing of the hood stripes. I painted them in a Craftsman II we have here.
- larrybl, MH81 and Sawdust have said thanks
#359
ONLINE
larrybl
-
- Site Supporter
- -GTt Supporter-
- Contributor
- Member No: 415
- 6,305 Thanks
- 4,038 posts
Texas Member
- Location: Central Texas
Posted June 16, 2016 - 07:48 AM
Nice masking! I just hope I can apply the large decals without buggering them up.
- KennyP said thank you
#360
OFFLINE
Phluphy
-
- Senior Member
- Member No: 70148
- 308 Thanks
- 401 posts
- Location: Central Gulf Coast Florida
Posted June 16, 2016 - 09:28 PM
If anyone is interested, this is the decal package. Kinda pricy at $130.00 or so, but I couldn't find them before.
Odd...the dash decal does not match my dash configuration. Where's the amp gauge?
- larrybl said thank you
