Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

D4-10 Clutch and throw-out bearing


  • Please log in to reply
8 replies to this topic

#1 subdude OFFLINE  

subdude
  • Member
  • Member No: 79242
  • 6 Thanks
  • 7 posts
  • Location: Pittsburgh, PA

Posted January 07, 2016 - 10:20 PM

Hi everyone, I was wondering if there is a certain replacement clutch and bearing for my D4-10?

Has the TR-10 engine if that matters.  Going to tear it apart, but the wife wants it back together in a timely manner so I would like to have parts on hand.  Sourcing for such parts would be much appreciated.

Thanks

 


  • Texas Deere and Horse said thank you

#2 Texas Deere and Horse OFFLINE  

Texas Deere and Horse

    RED Wild Hogs, Horses & Deeres

  • Staff Admin
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 1435
  • 14,676 Thanks
  • 15,456 posts
  • Location: East of San Antonio Texas

Posted January 07, 2016 - 10:36 PM

Welcome to GTtalk. I called this guy who sells Power King- Jim Dandy parts and ordered the parts I needed for my clutch in my D4-10

 

http://www.powerkingtractorbarn.com/

 

Here is a link to my D4-10, about page 4 is where I started working on my clutch,

 

http://gardentractor...-picture-heavy/

 

Hope this helps you out.


  • Bolens 1000, olcowhand, Alc and 5 others have said thanks

#3 boyscout862 ONLINE  

boyscout862
  • Senior Member
  • Contributor
  • Member No: 8923
  • 12,012 Thanks
  • 8,790 posts
  • Location: N.E. Connecticut

Posted January 08, 2016 - 12:52 AM

Welcome to GTT. Post pics when you can. Good Luck, Rick



#4 WNYTractorTinkerer ONLINE  

WNYTractorTinkerer

    Tinker Master

  • Senior Member
  • -GTt Supporter-
  • Member No: 10789
  • 9,865 Thanks
  • 5,507 posts
  • Location: Avon, NY

Posted January 08, 2016 - 05:09 AM

Welcome to the group Rick & good luck!   :welcome:



#5 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 35,842 Thanks
  • 44,594 posts
  • Location: Collinsville, Oklahoma

Posted January 08, 2016 - 05:34 AM

:wave: Welcome to the forum! Gonna need some pics of the machine! Check the link in my signature.



#6 Alc OFFLINE  

Alc

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 1094
  • 6,562 Thanks
  • 7,304 posts
  • Location: Bangor Pa

Posted January 08, 2016 - 06:13 AM

Welcome to GTTalk !!  Hope to see some pictures of your tractor some time



#7 sacsr OFFLINE  

sacsr

    Bush Hog Addict

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 4776
  • 3,436 Thanks
  • 3,354 posts
  • Location: Eastern NC

Posted January 08, 2016 - 06:31 AM

Being the TR-10 it is an early model- would love to get your serial number and see any pictures

#8 crittersf1 OFFLINE  

crittersf1

    GT Lunatic

  • Senior Member
  • Member No: 26142
  • 4,195 Thanks
  • 5,791 posts
  • Location: Newport, N.C.

Posted January 08, 2016 - 08:32 AM

:welcometogttalk: :camera:



#9 glgrumpy ONLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 8,452 Thanks
  • 7,818 posts
  • Location: Huntington, IN 46750 North East in State

Posted January 08, 2016 - 03:55 PM

Ebay has lots of those clutches if same as the Power Kings. Shop around a little, prices vary wildly on there.  That tractor barn guy is good source like said above. Mission Manufacturing in Southern INdiana is the PK parts source also. I've gotten the throw-out right from local auto store. Aetna brand. It's just the bearing and not the hardware attached to it, depending on what your brand does with it. A casting is used on PK's and it presses into that to mount. Pressure plates are more money, but can get the little arms, springs and pins seperately if yours is still pretty smooth. If you go to the Powr King forum here, I just posted a blow-up of the clutch they use and you can compare. Think trans is same too, but check.


  • subdude said thank you




Top