Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Wanted: Reverse cast pulley bracket


  • Please log in to reply
6 replies to this topic

#1 dblover OFFLINE  

dblover
  • Senior Member
  • Member No: 73516
  • 266 Thanks
  • 160 posts
  • Location: Lancaster,PA

Posted August 18, 2015 - 09:24 PM

http://www.americana...vert/aw132c.jpg


I need 1 part to finish my Big 5 db; the cast reverse bracket that the reverse shift rod attaches to on top and it pivots on the other lower reverser bracket.


Bracket is in top left in the above link. Thanks.

Attached Thumbnails

  • aw132c-1.jpeg


#2 Alc ONLINE  

Alc

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 1094
  • 5,458 Thanks
  • 6,627 posts
  • Location: Bangor Pa

Posted August 21, 2015 - 05:51 AM

Just checked the Pocono CL to see if the 2 DBs were still for sale one had reverse but it was one of the older ones so it might not have fit anyway. Is that bracket that model  only ?  Was yours missing or broken? On my 600 the bushings are worn pretty good , some day I'll need to address that


  • dblover said thank you

#3 IWLBCNU OFFLINE  

IWLBCNU

    Member

  • Senior Member
  • Member No: 5214
  • 120 Thanks
  • 157 posts
  • Location: Barboursville, VA

Posted August 21, 2015 - 06:59 AM

I'll try to look this weekend at what I have on some parts tractors, pretty sure it is there, but the wheel is locked up.



#4 dblover OFFLINE  

dblover
  • Senior Member
  • Member No: 73516
  • 266 Thanks
  • 160 posts
  • Location: Lancaster,PA

Posted August 21, 2015 - 07:39 AM

Just checked the Pocono CL to see if the 2 DBs were still for sale one had reverse but it was one of the older ones so it might not have fit anyway. Is that bracket that model only ? Was yours missing or broken? On my 600 the bushings are worn pretty good , some day I'll need to address that

My DB came with everything for the reverser except that little bracket/pulley. I have everything in the picture and the shift rod - except the bracket that runs from about 7 o'clock to the center of the pic. The bracket has a v-belt pulley on it that attaches to the middle of it.

Edited by dblover, August 21, 2015 - 07:55 AM.


#5 dblover OFFLINE  

dblover
  • Senior Member
  • Member No: 73516
  • 266 Thanks
  • 160 posts
  • Location: Lancaster,PA

Posted August 21, 2015 - 07:41 AM

I'll try to look this weekend at what I have on some parts tractors, pretty sure it is there, but the wheel is locked up.

It is better than nothing.  I am pretty good at fabbing parts/bushings.

 

The DB is very hard to move around without the reverser - unlike non-reverser models. (I have 2 DBs).



#6 dblover OFFLINE  

dblover
  • Senior Member
  • Member No: 73516
  • 266 Thanks
  • 160 posts
  • Location: Lancaster,PA

Posted August 21, 2015 - 07:52 AM

Here is another pic showing the bracket I seek. You can zoom in to see where the shift rod attaches to it near the right tire and its v-belt pulley for the outer trans pulley.

Attached Thumbnails

  • $_1-2.jpeg

Edited by dblover, August 21, 2015 - 07:56 AM.


#7 dblover OFFLINE  

dblover
  • Senior Member
  • Member No: 73516
  • 266 Thanks
  • 160 posts
  • Location: Lancaster,PA

Posted August 29, 2015 - 09:16 PM

I am set.  I just ordered the brackets from a guy posting DBs on CL in another state,


  • Alc said thank you




Top