Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

MF 620 Snow Blower Broke sprocket off


  • Please log in to reply
7 replies to this topic

#1 voltlord OFFLINE  

voltlord
  • Member
  • Member No: 53523
  • 2 Thanks
  • 4 posts
  • Location: Canada

Posted February 22, 2015 - 03:19 PM

Broke this part off the other day. Any one have any experience repairing this? do i have to disassemble auger. Part in manual i believe is part 56--- 1035021M9

 

AG2318-S, Single Pitch Sprocket Idler

 

Attached Thumbnails

  • Single-Pitch-Sprocket-Idlers.jpg

  • propane1 said thank you

#2 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 34,722 Thanks
  • 43,767 posts
  • Location: Collinsville, Oklahoma

Posted February 22, 2015 - 03:23 PM

:wave: Welcome to the forum! The Massey folks will be along!



#3 glgrumpy ONLINE  

glgrumpy

    Getting Out!

  • Senior Member
  • -GTt Supporter-
  • Member No: 8360
  • 8,272 Thanks
  • 7,658 posts
  • Location: Huntington, IN 46750 North East in State

Posted February 22, 2015 - 03:54 PM

Looks like that sprocket is pieces with a bearing? SO, did that explode or did the whole shaft break off?  If whole shaft, would think you will need more parts, like new shaft and the sprocket. If just sprocket broke, seems one could find that or replacement.



#4 voltlord OFFLINE  

voltlord
  • Member
  • Member No: 53523
  • 2 Thanks
  • 4 posts
  • Location: Canada

Posted February 22, 2015 - 03:57 PM

It looks like sprocket part is readily available does anyone know if the bracket that it fastens to is included if not where i can get one



#5 voltlord OFFLINE  

voltlord
  • Member
  • Member No: 53523
  • 2 Thanks
  • 4 posts
  • Location: Canada

Posted February 22, 2015 - 04:07 PM

Here is pic of actual parts that broke

Attached Thumbnails

  • IMG_20150222_155920.jpg

  • MH81 said thank you

#6 MH81 OFFLINE  

MH81

    Proud to be Deplorable

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 802
  • 29,954 Thanks
  • 29,757 posts
  • Location: N. W. PA

Posted February 22, 2015 - 04:09 PM

The bracket will not be included.
You might be able to find one thru Agco or our sponsors.
I would find a good welder in the area and flip him a couple of buck to reattach that pin, then get a new sprocket if needed.

#7 voltlord OFFLINE  

voltlord
  • Member
  • Member No: 53523
  • 2 Thanks
  • 4 posts
  • Location: Canada

Posted February 22, 2015 - 04:25 PM

Ok thanks, im a bad welder maybe i'll give it a go hahaha



#8 propane1 OFFLINE  

propane1
  • Senior Member
  • Member No: 54307
  • 7,859 Thanks
  • 3,825 posts
  • Location: Charlottetown, Prince Edward Island, Canada

Posted February 22, 2015 - 05:33 PM

I would get it re welded. Noel




Top