Some Clutch Pictures and Video
Started by
Bolens 1000
, Feb 19, 2011 08:52 PM
16 replies to this topic
#2
OFFLINE
1967bolens collector
-
- Senior Member
- Member No: 1920
- 652 Thanks
- 1,441 posts
Deceased
- Location: carney's point new jersey
Posted February 19, 2011 - 11:07 PM
lookin good doc!!!!!
#3
OFFLINE
Texas Deere and Horse
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 1435
- 14,521 Thanks
- 15,400 posts
RED Wild Hogs, Horses & Deeres
- Location: East of San Antonio Texas
Posted February 19, 2011 - 11:10 PM
Looks good Brian !!
#4
OFFLINE
bhts
-
- Senior Member
- -GTt Supporter-
- Sponsor
- Contributor
- Member No: 945
- 1,442 Thanks
- 2,140 posts
Bob's Lawn and Garden Tractors
- Location: ohio
Posted February 19, 2011 - 11:28 PM
Looks good Brian !!
#5
OFFLINE
Bill56
-
- Senior Member
- Member No: 60
- 839 Thanks
- 2,179 posts
Tractorholic
- Location: N. E. Illinois
Posted February 20, 2011 - 08:57 AM
Looks great, Brian. You did a nice job! Thanks for sharing the photos.
#6
OFFLINE
mjodrey
-
- Senior Member
- Contributor
- Member No: 92
- 2,353 Thanks
- 13,481 posts
Accumulator
- Location: Upper Granville, Nova Scotia, Canada
Posted February 20, 2011 - 10:12 AM
Thanks for sharing Brian, looks good.
#7
OFFLINE
gmud
-
- New Member
- Member No: 1749
- 3 Thanks
- 7 posts
New Member
- Location: MA
Posted February 20, 2011 - 12:06 PM
I see that unlike me, you wisely chose to install the throwout bearing holder the right way. You can imagine my delight when I got everything reinstalled, pressed down the clutch petal, and the two arms just pulled the bearing holder off the bearing...
#8
ONLINE
Bolens 1000
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 7
- 13,933 Thanks
- 17,721 posts
DR. Bolens
- Location: Western NY
Posted February 20, 2011 - 03:42 PM
I see that unlike me, you wisely chose to install the throwout bearing holder the right way. You can imagine my delight when I got everything reinstalled, pressed down the clutch petal, and the two arms just pulled the bearing holder off the bearing...
Usually when I do stuff like this I keep the parts list handy just to make sure I dont make a mistake LOL
Did you get it fixed?
#9
OFFLINE
Tinkerer
-
- Senior Member
- -GTt Supporter-
- Contributor
- Member No: 259
- 18 Thanks
- 200 posts
Tractorholic
- Location: Franklin, NH
Posted February 20, 2011 - 04:46 PM
Nice job on the clutch rebuild.
#10
OFFLINE
gmud
-
- New Member
- Member No: 1749
- 3 Thanks
- 7 posts
New Member
- Location: MA
Posted February 20, 2011 - 04:58 PM
Yeah, after a lot of cursing, another new bearing, and some more cursing, I got it straightened out.
#11
ONLINE
Bolens 1000
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 7
- 13,933 Thanks
- 17,721 posts
DR. Bolens
- Location: Western NY
Posted February 20, 2011 - 05:00 PM
I got it put back in the tractor today. It was around 25F. It wasn't the best conditions to be working on a clutch but I got the job done LOL.
Glad to hear you are up and running!
You may have mentioned it before but what model Bolens do you have?
Glad to hear you are up and running!
You may have mentioned it before but what model Bolens do you have?
#12
ONLINE
Bolens 1000
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 7
- 13,933 Thanks
- 17,721 posts
DR. Bolens
- Location: Western NY
Posted February 20, 2011 - 08:33 PM
Here is a sort video I made after the clutch was assembled. The other clutch I originally put on, the disc came loose so I just refurbished another clutch assembly to replace it.
Anyone have any suggestions on what I can use to bond the other disc back on?
still need to put the PTO back on
Had to be very careful when working on it not to scratch the paint LOL
Must have been a bad glue that was on that one disc. The small one is still holding but the big one let go.
Anyone have any suggestions on what I can use to bond the other disc back on?
still need to put the PTO back on
Had to be very careful when working on it not to scratch the paint LOL
Must have been a bad glue that was on that one disc. The small one is still holding but the big one let go.
Edited by Bolens 1000, February 20, 2011 - 08:39 PM.
#13
OFFLINE
Bigdaddydon
-
- Senior Member
- Contributor
- Member No: 1755
- 76 Thanks
- 230 posts
Tractorholic
- Location: St louis Missouri
Posted February 21, 2011 - 04:42 PM
Thanks for the video Brian,
Its nice to go for a ride even if your sitting in front of the computer.
Its nice to go for a ride even if your sitting in front of the computer.
#14
OFFLINE
Nascar3244888
-
- Senior Member
- Member No: 1218
- 164 Thanks
- 593 posts
Tractorholic
- Location: Douglassville, Pa.
Posted February 27, 2011 - 05:35 AM
Glad to see you have her going bud, did you redo the shaft yourself and where did you get or find the new parts you used????
#15
ONLINE
Bolens 1000
-
- Staff Admin
- Staff
- -GTt Supporter-
- Contributor
- Member No: 7
- 13,933 Thanks
- 17,721 posts
DR. Bolens
- Location: Western NY
Posted February 27, 2011 - 08:34 AM
Glad to see you have her going bud, did you redo the shaft yourself and where did you get or find the new parts you used????
Yeah, I did it myself
The friction discs were still good so I left them on. I got most of the bearings from NAPA, But the Big bearing that goes in the yoke I got that from my old Bolens dealer
