Just a shot in the dark but does anyone have a running onan cckb ms/2440h they want to sell
Tim
Engine
Started by
Tim Bergfeld
, Sep 14, 2014 10:51 PM
11 replies to this topic
#1
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 14, 2014 - 10:51 PM
#2
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 15, 2014 - 08:22 PM
No one lol
Tim
Tim
#3
OFFLINE
KennyP
-
- Super Moderator
- Staff
- -GTt Supporter-
- Contributor
- Member No: 2253
- 52479 Thanks
- 53087 posts
FORDoholic
- Location: Collinsville, Oklahoma
Posted September 16, 2014 - 06:25 AM
No CCKB's here, Tim. Only one P-220, a B43, & a B48G.
#4
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 16, 2014 - 03:42 PM
Ok so I wound up deciding to get mine sleeved and go back to a standard bore
Tim
Tim
#5
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 20, 2014 - 09:09 PM
Update dropped off the motor to get sleeved and I am getting the valves done to as well as the crank checked and the rods checked and I started painting engine covers and oil pan and pulleys today
Tim
Tim
- olcowhand said thank you
#6
OFFLINE
olcowhand
-
- Staff Admin
- Staff
- -GTt Supporter-
- Sponsor
- Contributor
- Member No: 20
- 44106 Thanks
- 32302 posts
Red Tractor Nut & Diesel Addict
- Location: South Central Kentucky
Posted September 20, 2014 - 09:12 PM
In the long run, you're going the best route. One can buy what the seller has known to be a great engine, then soon after something breaks that nobody had a clue was about to happen. This way you know exactly what's in there.
- GTTinkerer said thank you
#7
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 20, 2014 - 09:47 PM
Yup that is my plan
Tim
Tim
#8
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 20, 2014 - 09:53 PM
Every thing else works great on this thing. All three ranges were as smooth as silk rear 3 point works great mover spindles smooth as butter tires are fair but I want tri ribs in the front. I need a rear pto shaft and clutch but that will come
Tim
Tim
#9
OFFLINE
Cat385B
-
- Senior Member
- Contributor
- Member No: 8002
- 14751 Thanks
- 10288 posts
Tractorfanatics.com
- Location: MN
Posted September 20, 2014 - 11:21 PM
Every thing else works great on this thing. All three ranges were as smooth as silk rear 3 point works great mover spindles smooth as butter tires are fair but I want tri ribs in the front. I need a rear pto shaft and clutch but that will come
Tim
Grab two of those when you find them, please.
#10
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 21, 2014 - 06:13 AM
Anyone know what a complete shaft and clutch goes for
Tim
Tim
#11
OFFLINE
Cat385B
-
- Senior Member
- Contributor
- Member No: 8002
- 14751 Thanks
- 10288 posts
Tractorfanatics.com
- Location: MN
Posted September 21, 2014 - 08:39 AM
Joe's just sold a clutch on Ebay for a 4041. 9 bids, $124 winning bid.
#12
OFFLINE
Tim Bergfeld
-
- Senior Member
- Member No: 60783
- 219 Thanks
- 449 posts
Posted September 21, 2014 - 02:54 PM
Some one has a whole set up but they are saying it goes for around five hundred
Tim
Tim
