Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Which Carb On A Tec. Oh150


  • Please log in to reply
6 replies to this topic

#1 sodisr OFFLINE  

sodisr
  • Senior Member
  • Member No: 9153
  • 651 Thanks
  • 762 posts
  • Location: kenosha Wi

Posted December 11, 2013 - 11:12 AM

I'm having a heck of a time pinpointing  which carb is on my  bolens 1556- 01 ,, tec. engine,, oh150 or HH150 ??

 

     Serial # 1291E ---      on engine

  

      The carb shows a  walbro     LMH-1 on the top of the flange going into the head. The closest thing I see is a   LMH-10  ..

 

I also cannot find a manual for rebuilding it  or a parts list for it...There seems to be not much on manuals for the 1556,,,So should I try and go by somthing like the H14,,, or H16 ???

 

I would like to pull the carb and clean it but would like to have an exploded view of it first.. I don't want to get ahead of myself..

 

 

                Any help to get the closest info on this engine and carb would be greatly app.   Thanks   sodi.

 

 


  • MyBolens1053 said thank you

#2 PappyH OFFLINE  

PappyH

    New Member

  • Member
  • Member No: 7112
  • 35 Thanks
  • 53 posts
  • Location: North East Indiana

Posted December 11, 2013 - 11:44 AM

That is the same carb that is on my 1556.  I had to take mine apart for cleaning and it was pretty simple.  If you have had any other carbs apart you will be fine doing this one.  I agree there is not much to be found about the 1556 on the net.  Good luck, Bryan.


  • sodisr and MyBolens1053 have said thanks

#3 TAHOE ONLINE  

TAHOE
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 24522
  • 6,503 Thanks
  • 4,955 posts
  • Location: "Hamiltucky" Ohio

Posted December 11, 2013 - 12:34 PM

That is the standrad LMH carb, same used on the OH140 & OH160 motors. Usually if you buy a master rebuild kit, it has extra gaskets and parts to work on yours. I would say just buy a stadnard LMH kit and then when you tear yours apart, match the gaskets.

There are plenty of kits on Ebay, I usually buy from Randys engine repair, little more expensive, but he gets me the correct parts.


  • PappyH, sodisr and MyBolens1053 have said thanks

#4 Hydrohusky OFFLINE  

Hydrohusky
  • Member
  • Member No: 48182
  • 36 Thanks
  • 36 posts
  • Location: Fox Point, WI

Posted December 11, 2013 - 03:15 PM

I have an early 1556. It came equipped with an LMH-1 carb. It was leaking fuel into the air cleaner when the tank was full. Purchased a couple rebuild kits, but became frustrated because the kits were made for the LMH-1a revision of the carb. The LMH-1a uses a different needle/seat setup than the LMH-1. Now have a couple 1a carbs which work great! They came from OH/HH 140,150,160. Schematics from an LMH-1a should work fine for you.
  • MyBolens1053 said thank you

#5 MyBolens1053 OFFLINE  

MyBolens1053
  • Senior Member
  • Member No: 50025
  • 634 Thanks
  • 566 posts
  • Location: Martinsburg, WV (surrounded by Apple Orchards)

Posted December 11, 2013 - 03:46 PM

I did look into this and found a guy on youtube running into trouble with some of the Walbro LMH carburetors. There is a jet that you don't want to mess with unless you understand how it was put in to begin with. Other than that it's a very simple carb to work on.. Fuel pump, throttle body w/ needle and float.

 

Here's the video:

 

http://youtu.be/P0bvmOIfwF0


Edited by MyBolens1053, December 11, 2013 - 03:48 PM.

  • sodisr said thank you

#6 superaben OFFLINE  

superaben
  • Senior Member
  • Contributor
  • Member No: 11204
  • 7,664 Thanks
  • 5,677 posts
  • Location: Shenandoah Valley, VA

Posted December 11, 2013 - 06:45 PM

I can get you an LMH-1A kit OEM Walbro for $19.71.

 

Kit # is K1-LMH. 

 

Try this for an IPL:

 

Attached File  LMH1a.pdf   97.1KB   125 downloads

 

Ben W.


  • sodisr and MyBolens1053 have said thanks

#7 Newpaws493 OFFLINE  

Newpaws493
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 9454
  • 1,150 Thanks
  • 1,691 posts
  • Location: Boston,Massachusetts

Posted December 11, 2013 - 08:36 PM

Maybe this'll help. good luck

 

http://gardentractor...-engine-manual/

 

 

 

 

 

 


  • sodisr and MyBolens1053 have said thanks




Top