Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Removing 1886 Hydro Pump


  • Please log in to reply
9 replies to this topic

#1 bread320i OFFLINE  

bread320i
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 416
  • 593 Thanks
  • 1,220 posts
  • Location: Richfield Wisconsin

Posted August 18, 2013 - 09:02 PM

I am trying to replace the hydro from the rear end. I removed the bolt at the rear, the oil filter stud, and the break disk. I am having a hard time removing the pump. It looks like the gears are holding it back.

 

 



#2 blackjackjakexxix ONLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Sponsor
  • Member No: 2194
  • 2,350 Thanks
  • 1,758 posts
  • Location: Pulaski,Pa 16143

Posted August 19, 2013 - 08:47 AM

That should pop right out,there a little bulky man handleing,make sure you also removed  the coupler to the brake disk



#3 wilberj ONLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,194 Thanks
  • 5,213 posts
  • Location: Michigan

Posted August 19, 2013 - 09:18 AM

Sould pop out just try to tip it down aswell so the back gets off the gears.



#4 bread320i OFFLINE  

bread320i
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 416
  • 593 Thanks
  • 1,220 posts
  • Location: Richfield Wisconsin

Posted August 19, 2013 - 12:12 PM

I have been wacking it darn hard with a big hammer and it is bearly coming out, but is coming slowly. I guess I'll try a bigger hammer.



#5 wilberj ONLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,194 Thanks
  • 5,213 posts
  • Location: Michigan

Posted August 19, 2013 - 07:05 PM

I have been wacking it darn hard with a big hammer and it is bearly coming out, but is coming slowly. I guess I'll try a bigger hammer.

 

There must be something holding you up.

 

You taken the shaft with the allen head out of the filter area right?

The top cover is off to?



#6 bread320i OFFLINE  

bread320i
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 416
  • 593 Thanks
  • 1,220 posts
  • Location: Richfield Wisconsin

Posted August 20, 2013 - 06:00 AM

Yup I removed the oil filter stud. Pulled the break disk off and necessary collar, the large bolt at the rear. Using a hammer I did get it to move 1/4" but thats when I stopped thinking something else is keeping it from coming out.



#7 blackjackjakexxix ONLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Sponsor
  • Member No: 2194
  • 2,350 Thanks
  • 1,758 posts
  • Location: Pulaski,Pa 16143

Posted August 20, 2013 - 09:14 AM

How about that top plate cover where the shifter rod goes on



#8 wilberj ONLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,194 Thanks
  • 5,213 posts
  • Location: Michigan

Posted August 20, 2013 - 10:44 AM

How about that top plate cover where the shifter rod goes on

Ditto



#9 bread320i OFFLINE  

bread320i
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 416
  • 593 Thanks
  • 1,220 posts
  • Location: Richfield Wisconsin

Posted August 20, 2013 - 01:00 PM

How about that top plate cover where the shifter rod goes on

 

The "park, neutral, drive rod? On the top of the rear end, yes I removed that and the cover for the rear end too.



#10 blackjackjakexxix ONLINE  

blackjackjakexxix

    Blackjackjakexxix

  • Senior Member
  • Sponsor
  • Member No: 2194
  • 2,350 Thanks
  • 1,758 posts
  • Location: Pulaski,Pa 16143

Posted August 20, 2013 - 03:21 PM

Really can't figure out why it won't come out






Top