Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Where Is The Part Number On My Eaton Hydro


  • Please log in to reply
10 replies to this topic

#1 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted May 30, 2013 - 05:24 PM

I have a Massey 1650 with stripped splines and need to know where to find the part number on the Hydro so I can try to get a new input shaft.  Thanks



#2 bhts OFFLINE  

bhts

    Bob's Lawn and Garden Tractors

  • Senior Member
  • -GTt Supporter-
  • Sponsor
  • Contributor
  • Member No: 945
  • 1,413 Thanks
  • 2,117 posts
  • Location: ohio

Posted May 30, 2013 - 08:06 PM

The part number for the shaft you are looking for is 7013733


  • olcowhand and outdoorsmanjw have said thanks

#3 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted May 30, 2013 - 08:11 PM

Thanks Sir



#4 limebuzz ONLINE  

limebuzz

    Member

  • Senior Member
  • Member No: 795
  • 863 Thanks
  • 879 posts
  • Location: Bluevale Ontario

Posted June 01, 2013 - 04:16 AM

I have the same problem with a 1650 that I just picked up.i am looking for solutions to get it up and operational again.Massey says the shaft is obsolete. So I found a place that made me one hardended and all for a mear $350. The shaft is too hard for me to get a weld to bond to it,so I am at a stand still and the grass isn't.If you find a way to fix this I would love to hear about it.Good luck



#5 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted June 01, 2013 - 01:44 PM

Limebuzz I am trying to get a new shaft from a hydraulic shop if they can get me one.  I will let you know what I come up with.  I might have to turn to my dad for help he has all the tools and machines I would ever need.  One thought is to take the shaft out of the housing so you can get some heat to it without worry to get it to weld right.  He could machine on for me if I can't find one probably.  I will keep you updated.

Thanks


  • limebuzz said thank you

#6 limebuzz ONLINE  

limebuzz

    Member

  • Senior Member
  • Member No: 795
  • 863 Thanks
  • 879 posts
  • Location: Bluevale Ontario

Posted June 01, 2013 - 04:30 PM

Thanks a lot!I had one made for my 1450 a couple years ago but that is ridiculous $ for a little shaft.I was thinking about taking it out to weld it but I cant figure what to weld on it in order to fit back through the case?



#7 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted June 01, 2013 - 05:01 PM

Yeah I am trying to be cheap with it I only paid 450 for it and the motor runs and has rear PTO and 3 point hitch too.  Once I get the shaft done going to see if every thing works good then will probably paint it



#8 ENafziger OFFLINE  

ENafziger
  • Senior Member
  • Member No: 45112
  • 254 Thanks
  • 254 posts
  • Location: Knoxville, TN

Posted August 26, 2015 - 04:08 PM

Did you every find a solution for this?  I'm in the same boat with my 1650.  I welded the shaft to the coupling with a 6011 root pass and 7018 cover...using 3/32 rods and a wet rag around the front seal of the hydro pump.  It lasted for about 2 hours.  It looks like the hardened shaft is hard to get good penetration on while keeping heat down to the seal.



#9 limebuzz ONLINE  

limebuzz

    Member

  • Senior Member
  • Member No: 795
  • 863 Thanks
  • 879 posts
  • Location: Bluevale Ontario

Posted August 26, 2015 - 07:25 PM

Did you every find a solution for this?  I'm in the same boat with my 1650.  I welded the shaft to the coupling with a 6011 root pass and 7018 cover...using 3/32 rods and a wet rag around the front seal of the hydro pump.  It lasted for about 2 hours.  It looks like the hardened shaft is hard to get good penetration on while keeping heat down to the seal.

I just had another one strip on me last week. Now I have a pile of 3 that all need new shafts.  



#10 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted August 26, 2015 - 08:07 PM

Here's the contact info for the shaft.    I never did buy one but he did have the parts I needed. 
 
L J Fluid Power
10118 S M-43 Hwy
Delton, MI 49046

  • limebuzz and ENafziger have said thanks

#11 outdoorsmanjw OFFLINE  

outdoorsmanjw

    New Member

  • Member
  • Member No: 3564
  • 70 Thanks
  • 83 posts
  • Location: Florence KY

Posted August 26, 2015 - 08:12 PM

1100 025

J11H CCW
 
Part numbers

  • limebuzz said thank you




Top