Jump to content

Garden Tractors and Parts on eBay



Photo
- - - - -

Here Is The Size Of A Ford / Jacobsen Manual Pto Clutch Gauge


  • Please log in to reply
13 replies to this topic

#1 chris m OFFLINE  

chris m

    Tractorholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 8148
  • 3,334 Thanks
  • 4,060 posts
  • Location: Charlestown,Rhode Island

Posted December 04, 2012 - 07:56 PM

I bought this from Messics back awhile ago. I believe she said it was the last one. and she found it at a dealer out West.

I know people have wondered what the correct size gap for adjusting the clutch was. So here are the measurements of the tool. The thickness is the only thing that really matters.
scan0001.jpg

Not sure why it got cut off but it will work :D

If you can't see it large enough the thickness is .0468 (3/64)

I should add this is for the old Ford 80,100,120,140 Jacobsen chief 800,1000,1200

Edited by chris m, December 04, 2012 - 07:59 PM.

  • KennyP, Russ and Arti have said thanks

#2 Farmlife OFFLINE  

Farmlife

    Tractor Whisperer

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 12309
  • 1,233 Thanks
  • 1,461 posts

Posted December 05, 2012 - 04:20 AM

I don't have a use for one yet, but what a great thing to share. I'm sure alota people will get alota use from it. Thanks. such a simple design.
  • chris m said thank you

#3 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 05, 2012 - 05:24 AM

Neat tool you got there. Thanks for sharing it with the members.
  • chris m said thank you

#4 HankS OFFLINE  

HankS

    Member

  • Senior Member
  • Contributor
  • Member No: 7608
  • 48 Thanks
  • 107 posts
  • Location: Brighton, MI

Posted December 05, 2012 - 07:33 PM

Thank you! I tried to find the specs last year when putting a manual PTO back together on a Ford 120. Couldn't find anyhting, except references to the Jac tool.

#5 chris m OFFLINE  

chris m

    Tractorholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 8148
  • 3,334 Thanks
  • 4,060 posts
  • Location: Charlestown,Rhode Island

Posted December 05, 2012 - 07:38 PM

Thank you! I tried to find the specs last year when putting a manual PTO back together on a Ford 120. Couldn't find anyhting, except references to the Jac tool.

NP! I ran into the same problem. And in all my searching I never found the size of this tool. So everyone will have it now! :D

#6 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 05, 2012 - 08:22 PM

Here real soon, I will make a drawing of this and put it in the Ford Manuals section for everyone to download as needed. I'll post the link in this thread.
  • chris m said thank you

#7 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 06, 2012 - 07:05 PM

One question. How far is the 1/2" hole from the end? Or does it matter?

#8 chris m OFFLINE  

chris m

    Tractorholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 8148
  • 3,334 Thanks
  • 4,060 posts
  • Location: Charlestown,Rhode Island

Posted December 06, 2012 - 07:15 PM

One question. How far is the 1/2" hole from the end? Or does it matter?

it doesn't matter, that is just to hang it up.but it is 1/2" on center
  • KennyP said thank you

#9 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 06, 2012 - 07:31 PM

Okay. Then I'm done with it.
Clutch Tool.jpeg
How's this?
  • chris m said thank you

#10 chris m OFFLINE  

chris m

    Tractorholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 8148
  • 3,334 Thanks
  • 4,060 posts
  • Location: Charlestown,Rhode Island

Posted December 06, 2012 - 07:44 PM

Awesome Kenny! One question though, how come it doesn't come out of my printer @ the 3/64"? :bigrofl:
  • KennyP said thank you

#11 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 06, 2012 - 07:50 PM

You need to calibrate the printer.

#12 chris m OFFLINE  

chris m

    Tractorholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 8148
  • 3,334 Thanks
  • 4,060 posts
  • Location: Charlestown,Rhode Island

Posted December 06, 2012 - 07:59 PM

Oh.... So I guess I don't have to waste 10 sheets of printer paper now! LOL

Thanks again Kenny :thumbs:

#13 KennyP ONLINE  

KennyP

    FORDoholic

  • Super Moderator
  • Staff
  • -GTt Supporter-
  • Contributor
  • Member No: 2253
  • 36,369 Thanks
  • 44,911 posts
  • Location: Collinsville, Oklahoma

Posted December 06, 2012 - 08:02 PM

Here's the Link for the .pdf file.
  • chris m said thank you

#14 HankS OFFLINE  

HankS

    Member

  • Senior Member
  • Contributor
  • Member No: 7608
  • 48 Thanks
  • 107 posts
  • Location: Brighton, MI

Posted December 09, 2012 - 04:48 PM

Okay. Then I'm done with it.
Clutch Tool.jpeg
How's this?


That looks good. The important thing is knowing it's 3/64" thick. You can use 2 feeler gauges to get it pretty close.




Top