Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Owners Manual Snow Blade For 1600 Eliminator


  • Please log in to reply
6 replies to this topic

#1 pgcg4life OFFLINE  

pgcg4life
  • Member
  • Member No: 8646
  • 0 Thanks
  • 10 posts
  • Location: Ellenville, NY

Posted October 14, 2012 - 06:31 PM

Does anyone have a owners manual for the snow blade for the Eliminator series. Just got my 1668 last week, but no manuals. Trying to figure out if I have all the parts and how to attach it. Any help would be greatly appreciated.

#2 bhts OFFLINE  

bhts

    Bob's Lawn and Garden Tractors

  • Senior Member
  • -GTt Supporter-
  • Sponsor
  • Contributor
  • Member No: 945
  • 1,413 Thanks
  • 2,117 posts
  • Location: ohio

Posted October 14, 2012 - 08:53 PM

I should have it but what is the model number of your blade.
  • pgcg4life said thank you

#3 Delmar ONLINE  

Delmar
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 5039
  • 2,323 Thanks
  • 2,416 posts
  • Location: west central missouri

Posted October 14, 2012 - 09:21 PM

I used to have a 1668 and a snow blade. I still have the manual. You can find another copy of it in the manuals section of this site. (it is located in the bar on the top of the web page) It is called Snow Blade Attachment 42 inch # 18305 I gave you a short cut....click on the address below

http://gardentractor...n-snowbladepdf/


there is also a manual for your tractor in the manuals section

Those are great tractors. That is a good motor in it. Mine had a 16 hp briggs in it.

Edited by JBBR, October 14, 2012 - 09:56 PM.

  • pgcg4life said thank you

#4 pgcg4life OFFLINE  

pgcg4life
  • Member
  • Member No: 8646
  • 0 Thanks
  • 10 posts
  • Location: Ellenville, NY

Posted October 15, 2012 - 08:31 AM

bhts - Blade has been painted over several times. It's 42" wide and I'm trying to find out how to properly attach the lift tube to the tractor.

JBBR - Thanks. I've already downloaded the parts manual. Looking for the owners manual.

#5 Delmar ONLINE  

Delmar
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 5039
  • 2,323 Thanks
  • 2,416 posts
  • Location: west central missouri

Posted October 15, 2012 - 07:08 PM

I have an owners manual. i will see if my wife can scan it for me. She has a scanner at her office. Here's some pics with my camera


[attachment=46526:100_8832.jpg]
[attachment=46527:100_8839.jpg]
[attachment=46528:100_8840.jpg]
[attachment=46529:100_8841.jpg]
[attachment=46530:100_8842.jpg]
[attachment=46531:100_8843.jpg]
[attachment=46532:100_8844.jpg]
[attachment=46533:100_8845.jpg]
[attachment=46534:100_8846.jpg]
[attachment=46535:100_8847.jpg]
  • pgcg4life said thank you

#6 pgcg4life OFFLINE  

pgcg4life
  • Member
  • Member No: 8646
  • 0 Thanks
  • 10 posts
  • Location: Ellenville, NY

Posted October 15, 2012 - 07:21 PM

That's what I was looking for. If its not raining tomorrow I'll give it a whirl.

#7 pgcg4life OFFLINE  

pgcg4life
  • Member
  • Member No: 8646
  • 0 Thanks
  • 10 posts
  • Location: Ellenville, NY

Posted October 16, 2012 - 06:00 PM

Alright, I didn't have too much time to get the plow attached. Did however quickly pull up to it with the lift tube under the tractor. Discovered that I don't have a clevis pin to use, minor issue. But looking at how it would attach, I'm a bit confused as how it actually would lift the plow. Mine has the hydraulic lift, the holes where the tube will attach is towards the rear of tractor in the up position. Wouldn't this actually lower the plow? Is the lift cylinder extended or retracted in the up position? Thanks

Edited by pgcg4life, October 17, 2012 - 08:26 AM.





Top