Jump to content

Nominations for Tractor of the Month
Garden Tractors and Parts on eBay



Photo
- - - - -

Mounting Large Frame Tiller


  • Please log in to reply
6 replies to this topic

#1 OldBuzzard ONLINE  

OldBuzzard

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 805
  • 6,480 Thanks
  • 4,633 posts
  • Location: Oberlin, OH

Posted January 31, 2012 - 01:16 PM

OK, danged near 60 Deg here so I'm wanting to mount the tiller on the 1886.

Question is...which set of holes do I use :confuse::confuse:

The top ones, or the larger bottom ones :confuse::confuse:

#2 bhts OFFLINE  

bhts

    Bob's Lawn and Garden Tractors

  • Senior Member
  • -GTt Supporter-
  • Sponsor
  • Contributor
  • Member No: 945
  • 1,413 Thanks
  • 2,115 posts
  • Location: ohio

Posted January 31, 2012 - 01:33 PM

Pins go in the bottom holes and then mount tiller then put pins in the top holes so not to bounce out.

#3 wilberj OFFLINE  

wilberj
  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 51
  • 4,179 Thanks
  • 5,205 posts
  • Location: Michigan

Posted January 31, 2012 - 02:20 PM

Pins go in the bottom holes and then mount tiller then put pins in the top holes so not to bounce out.



:ditto:

#4 OldBuzzard ONLINE  

OldBuzzard

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 805
  • 6,480 Thanks
  • 4,633 posts
  • Location: Oberlin, OH

Posted January 31, 2012 - 04:36 PM

Thank ya...

I got it mounted...after a trip to get some mounting pins and hairclips.

Gonna have to shorten the lift arms. They are adjusted too far out, and it won't lift the tiller.

Huess I'll do that tomorrow.

#5 8tyman8 OFFLINE  

8tyman8

    Member

  • Senior Member
  • GTt Junior
  • Member No: 5455
  • 414 Thanks
  • 731 posts
  • Location: kingston ont canada

Posted January 31, 2012 - 09:25 PM

would love to see some vids of it tilling

#6 OldBuzzard ONLINE  

OldBuzzard

    Tractorholic

  • Senior Member
  • -GTt Supporter-
  • Contributor
  • Member No: 805
  • 6,480 Thanks
  • 4,633 posts
  • Location: Oberlin, OH

Posted January 31, 2012 - 10:08 PM

Dunno if that will happen or not.

Tractor has a home made FEL on it, and I don't know if the PTO shaft will clear the cross member going under the frame.

I hope it does, because I pland on plowing and tilling about a 1/4 acre this spring/summer. If now I'll have t o use a 1256 with a 33" round back tiller instead of this 40" square back.

#7 1967bolens collector OFFLINE  

1967bolens collector

    Tractorholic

  • Senior Member
  • Member No: 1920
  • 648 Thanks
  • 1,437 posts
  • Location: carney's point new jersey

Posted February 02, 2012 - 12:50 AM

Dunno if that will happen or not.

Tractor has a home made FEL on it, and I don't know if the PTO shaft will clear the cross member going under the frame.

I hope it does, because I pland on plowing and tilling about a 1/4 acre this spring/summer. If now I'll have t o use a 1256 with a 33" round back tiller instead of this 40" square back.




anyway you can notch the loader frame then try to brace it so its not weak from cutting it? hope you get it going




Top